VLANs and Trunking

Chapter Description

Learn how to configure, assign ports, and trunk VLANs on Cisco hardware.

6-1: VLAN Configuration

  • VLANs are broadcast domains defined within switches to allow control of broadcast, multicast, unicast, and unknown unicast within a Layer 2 device.

  • VLANs are defined on a switch in an internal database known as the VLAN Trunking Protocol (VTP) database. After a VLAN has been created, ports are assigned to the VLAN.

  • VLANs are assigned numbers for identification within and between switches. Cisco switches have two ranges of VLANs, the normal range and extended range.

  • VLANs have a variety of configurable parameters, including name, type, and state.

  • Several VLANs are reserved, and some can be used for internal purposes within the switch.

Creation of an Ethernet VLAN

VLANs are created on Layer 2 switches to control broadcasts and enforce the use of a Layer 3 device for communications. Each VLAN is created in the local switch's database for use. If a VLAN is not known to a switch, that switch cannot transfer traffic across any of its ports for that VLAN. VLANs are created by number, and there are two ranges of usable VLAN numbers (normal range 1–1000 and extended range 1025–4096). When a VLAN is created, you can also give it certain attributes such as a VLAN name, VLAN type, and its operational state. To create a VLAN, use the following steps.

  1. Configure VTP.

    VTP is a protocol used by Cisco switches to maintain a consistent database between switches for trunking purposes. VTP is not required to create VLANs; however, Cisco has set it up to act as a conduit for VLAN configuration between switches as a default to make administration of VLANs easier. Because of this, you must first either configure VTP with a domain name or disable VTP on the switch. VTP is explained in detail in section "6-4: VLAN Trunking Protocol."

    NOTE

    For Catalyst 4000 and 6000 switches running IOS Supervisor 12.1(8a) or above (native IOS), you can configure the VTP parameters in global configuration mode as well.

    • Specify a VTP name:

      COS

      set vtp domain domain-name

      IOS

      (vlan) vtp domain domain-name

      -OR-

      (global) vtp domain domain-name


      By default, the VTP is in server mode and must be configured with a domain name before any VLANs can be created. These commands specify the VTP domain name. For IOS switches, you enter vlan database mode, (vlan), by entering the command vlan database, at the privileged-level prompt.

      NOTE

      The global configuration command vtp domain is not available on all switches that run IOS.

    -OR-

    • Disable VTP synchronization:

      COS

      set vtp mode transparent

      IOS

      (vlan) vtp transparent

      -OR-

      (global) vtp mode transparent


      Another option is to disable VTP synchronization of the databases. Disabling it enables you to manage your local VTP database without configuring and relying on VTP. For Catalyst 4000 and 6000 switches running IOS Supervisor 12.1(8a) or above (native IOS), you can configure the VTP parameters in global configuration mode as well.

      NOTE

      The global configuration command vtp mode transparent is not available on all switches that run IOS.

    -OR-

    • Disable VTP:

      COS

      set vtp mode off

      IOS

      N/A


      With the introduction of COS version 7.1.1, an option now exists to disable VTP completely. Use the command set vtp mode off to turn off VTP. After doing so, you can administer the local VTP database.

  2. Create the VLAN.

    VLANs are created by number. The two ranges of VLANs are as follows:

    • The standard range consists of VLANs 1 to 1000.

    • The extended range consists of VLANs 1025 to 4096.

    Extended VLANs are currently supported only on switches running COS software version 6.1 or greater. When you create a VLAN, you have many options to consider. Many options are valid only for FDDI and Token Ring VLANs. Some of the items configured deal with options, such as private VLANs, which are discussed in other sections in this book. VLANs are created using the set vlan command for COS devices or with the vlan command in vlan database mode for IOS switches. For Ethernet VLANs, you can also configure the standard parameters in Table 6-1.

    Table 6-1 Configurable VLAN Parameters

    Parameter

    Description

    name

    A description of the VLAN up to 32 characters. If none is given, it defaults to VLAN00XXX, where xxx is the VLAN number.

    mtu

    The maximum transmission unit (packet size, in bytes) that the VLAN can use; valid values are from 576 to 18190. The MTU can extend up to 1500 for Ethernet, but beyond for Token Ring or FDDI. The default is 1500.

    state

    Used to specify whether the state of the VLAN is active or suspended. All ports in a suspended VLAN will be suspended and not allowed to forward traffic. The default state is active.


    NOTE

    Many other options are available during the VLAN configuration command; however, most of these deal with the configuration of FDDI and Token Ring VLANs. Because these are not widely used topologies, the options and descriptions of Token Ring and FDDI VLAN configuration and parameters have not been included in this book. For information on Token Ring or FDDI VLANs, refer to http://www.cisco.com/univercd/cc/td/doc/product/ lan/cat5000/rel_6_3/config/vlans.htm.

    1. Create a VLAN in the standard range:

      COS

      set vlan vlan-id [name name] [state state] [mtu mtu]

      IOS

      (vlan) vlan vlan-id [name vlan-name] [state {suspend | active}] [mtu mtu-size]

      (global) vlan vlan-id

      (vlan-config) vlan vlan-id [mtu mtu-size] [name vlan-name] [state {suspend | active}]


      The vlan-id specifies the VLAN by number. For COS you can specify a range of VLANs in the vlan-id section; you cannot configure the name for a range of VLANs, however, because each VLAN is to have a unique name. For IOS switches, VLANs are created in vlan database mode. For Catalyst 6000 and 4000 switches running Supervisor IOS 12.1(8a) and above, you can create VLANs in global configuration mode if the switch is in VTP transparent mode. To do this, enter the vlan vlan-id command to move to vlan-config mode. From vlan-config mode, you can manage the parameters of the VLANs.

      NOTE

      You cannot modify any of the parameters for VLAN 1.

    2. Create a VLAN in the extended range.

      Extended VLANs support VLANs up to 4096 in accordance with the 802.1Q standard. Currently only switches running COS 6.1 or greater can support creation and assignment of VLANs in the extended range. You cannot currently use VTP to manage VLANs in the extended range, and these VLANs cannot be passed over an Inter-Switch Link (ISL) trunk link.

      1. Enable spanning-tree MAC reduction:

        COS

        set spantree macreduction enable

        IOS

        N/A


        To allow these switches to use the extended range, you must first enable spanningtree macreduction to allow the switch to support a large number of spanning-tree instances with a very limited number of MAC addresses and still maintain the IEEE 802.1D bridge ID requirement for each STP instance.

        NOTE

        After you have created a VLAN in the extended range, you cannot disable this feature unless you first delete the VLAN.

      2. Create a VLAN in the extended range:

        COS

        set vlan vlan-id [name name] [state state] [mtu mtu]

        IOS

        N/A


        Here the vlan-id would be a number from 1025 to 4096. Numbers 1001 to 1024 are reserved by Cisco and cannot be configured.

        CAUTION

        For Catalyst 6000 series switches with FlexWAN cards, the system identifies these ports internally with VLAN numbers starting with 1025. If you have any FlexWAN modules, be sure to reserve enough VLAN numbers (starting with VLAN 1025) for all the FlexWAN ports you want to install. You cannot use these extended VLANs if you install FlexWAN ports.

Feature Example

In this example, the switches Access_1 and Distribution_1 are going to be configured with VLANs 5, 8, and 10 with the names Cameron, Logan, and Katie, respectively. Also the distribution switch will be configured with VLAN 2112 with the name Rush.

An example of the Catalyst OS configuration for Distribution 1 follows:

Distribution_1 (enable)>set vtp mode transparent
Distribution_1 (enable)>set vlan 5 name Cameron
Distribution_1 (enable)>set vlan 8 name Logan
Distribution_1 (enable)>set vlan 10 name Katie
Distribution_1 (enable)>set spantree macreduction enable
Distribution_1 (enable)>set vlan 2112 name Rush
Distribution_1 (enable)>

An example of the Supervisor IOS configuration for Distribution 1 follows:

Distribution_1#vlan database
Distribution_1(vlan)#vtp transparent
Distribution_1(vlan)#exit
Distribution_1#conf t
Distribution_1(config)#vlan 5 
Distribution_1(config-vlan)# name Cameron
Distribution_1(config-vlan)#vlan 8 
Distribution_1(config-vlan)# name Logan
Distribution_1(config-vlan)# vlan 10
Distribution_1(config-vlan)# name Katie
Distribution_1(config-vlan)# end
Distribution_1 #copy running-config startup-config

NOTE

For the Supervisor IOS, extended VLANs such as 2112 are not supported.

An example of the Layer 2 IOS configuration for Access 1 follows:

Access_1#vlan database
Access_1 (vlan)#vtp transparent
Access_1 (vlan)#vlan 5 name Cameron
Access_1 (vlan)#vlan 8 name Logan
Access_1 (vlan)#vlan 10 name Katie
Access_1 (vlan)#exit
Access_1#copy running-config startup-config
2. VLAN Port Assignments | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020