Dynamic Routing Protocols

  • Sample Chapter is provided courtesy of Cisco Press.
  • Date: Nov 16, 2001.

Chapter Description

This sample chapter from CCIE: Routing TCP/IP Volume I shows how routers can discover how to correctly switch packets to their respective destinations automatically and share that information with other routers via dynamic routing protocols.

The last chapter explained what a router needs to know to correctly switch packets to their respective destinations and how that information is put into the route table manually. This chapter shows how routers can discover this information automatically and share that information with other routers via dynamic routing protocols. A routing protocol is the language a router speaks with other routers in order to share information about the reachability and status of networks.

Dynamic routing protocols not only perform these path determination and route table update functions but also determine the next-best path if the best path to a destination becomes unusable. The capability to compensate for topology changes is the most important advantage dynamic routing offers over static routing.

Obviously, for communications to occur the communicators must speak the same language. There are eight major IP routing protocols from which to choose; if one router speaks RIP and another speaks OSPF, they cannot share routing information because they are not speaking the same language. Subsequent chapters examine all the IP routing protocols in current use, and even consider how to make a router "bilingual," but first it is necessary to explore some characteristics and issues common to all routing protocols—IP or otherwise.

Routing Protocol Basics

All dynamic routing protocols are built around an algorithm. Generally, an algorithm is a step-by-step procedure for solving a problem. A routing algorithm must, at a minimum, specify the following:

  • A procedure for passing reachability information about networks to other routers

  • A procedure for receiving reachability information from other routers

  • A procedure for determining optimal routes based on the reachability information it has and for recording this information in a route table

  • A procedure for reacting to, compensating for, and advertising topology changes in an internetw_ork

A few issues common to any routing protocol are path determination, metrics, convergence, and load balancing.

Path Determination

All networks within an internetwork must be connected to a router, and wherever a router has an interface on a network that interface must have an address on the network. This address is the originating point for reachability information.

Figure 4.1 shows a simple three-router internetwork. Router A knows about networks 192.168.1.0, 192.168.2.0, and 192.168.3.0 because it has interfaces on those networks with corresponding addresses and appropriate address masks. Likewise, router B knows about 192.168.3.0, 192.168.4.0, 192.168.5.0, and 192.186.6.0; router C knows about 192.168.6.0, 192.168.7.0, and 198.168.1.0. Each interface implements the data link and physical protocols of the network to which it is attached, so the router also knows the state of the network (up or down).

Figure 4.1 Each router knows about its directly connected networks from its assigned addresses and masks.

At first glance, the information-sharing procedure seems simple. Look at router A:

  1. Router A examines its IP addresses and associated masks and deduces that it is attached to networks 192.168.1.0, 192.186.2.0, and 192.168.3.0.

  2. Router A enters these networks into its route table, along with some sort of flag indicating that the networks are directly connected.

  3. Router A places the information into a packet: "My directly connected networks are 192.168.1.0, 192.186.2.0, and 192.168.3.0."

  4. Router A transmits copies of these route information packets, or routing updates, to routers B and C.

  5. Routers B and C, having performed the same steps, have sent updates with their directly connected networks to A. Router A enters the received information into its route table, along with the source address of the router that sent the update packet. Router A now knows about all the networks, and it knows the addresses of the routers to which they are attached.

This procedure does seem quite simple. So why are routing protocols so much more complicated than this? Look again at Figure 4.1.

  • What should router A do with the updates from B and C after it has recorded the information in the route table? Should it, for instance, pass B's routing information packet to C and pass C's packet to B?

  • If router A does not forward the updates, information sharing may not be complete. For instance, if the link between B and C does not exist, those two routers would not know about each other's networks. Router A must forward the update information, but this step opens a whole new set of problems.

  • If router A hears about network 192.168.4.0 from both router B and router C, which router should be used to reach that network? Are they both valid? Which one is the best path?

  • What mechanism will be used to ensure that all routers receive all routing information while preventing update packets from circulating endlessly through the internetwork?

  • The routers share certain directly connected networks (192.168.1.0, 192.168.3.0, and 192.168.6.0). Should the routers still advertise these networks?

These questions are almost as simplistic as the preceding preliminary explanation of routing protocols, but they should give you a feel for some of the issues that contribute to the complexity of the protocols. Each routing protocol addresses these questions one way or another, as will become clear in following sections and chapters.

Metrics

When there are multiple routes to the same destination, a router must have a mechanism for calculating the best path. A metric is a variable assigned to routes as a means of ranking them from best to worst or from most preferred to least preferred. Consider the following example of why metrics are needed.

Assuming that information sharing has properly occurred in the internetwork of Figure 4.1, router A might have a route table that looks like Table 4.1.

Table 4.1 A rudimentary route table for router A of Figure 4.1.

Network

Next-Hop Router

192.168.1.0

Directly connected

192.168.2.0

Directly connected

192.168.3.0

Directly connected

192.168.4.0

B, C

192.168.5.0

B, C

192.168.6.0

B, C

192.168.7.0

B, C


This route table says that the first three networks are directly connected and that no routing is needed from router A to reach them, which is correct. The last four networks, according to this table, can be reached via router B or router C. This information is also correct. But if network 192.168.7.0 can be reached via either router B or router C, which path is the preferable path? Metrics are needed to rank the alternatives.

Different routing protocols use different, and sometimes multiple, metrics. For example, RIP defines the "best" route as the one with

Hop Count

A hop count metric simply counts router hops. For instance, from router A it is 1 hop to network 192.168.5.0 if packets are sent out interface 192.168.3.1 (through router B) and 2 hops if packets are sent out 192.168.1.1 (through routers C and B). Assuming hop count is the only metric being applied, the best route is the one with the fewest hops, in this case, A-B.

But is the A-B link really the best path? If the A-B link is a DS-0 link and the A-C and C-B links are T-1 links, the 2-hop route may actually be best because bandwidth plays a role in how efficiently traffic travels through the network.

Bandwidth

A bandwidth metric would choose a higher-bandwidth path over a lower-bandwidth link. However, bandwidth by itself still may not be a good metric. What if one or both of the T1 links are heavily loaded with other traffic and the 56K link is lightly loaded? Or what if the higher-bandwidth link also has a higher delay?

Load

This metric reflects the amount of traffic utilizing the links along the path. The best path is the one with the lowest load.

Unlike hop count and bandwidth, the load on a route changes, and therefore the metric will change. Care must be taken here. If the metric changes too frequently, route flapping—the frequent

Delay

Delay is a measure of the time a packet takes to traverse a route. A routing protocol using delay as a metric would choose the path with the least delay as the best path. There may be many ways to measure delay. Delay may take into account not only the delay of the links along the route but also such factors as router latency and queuing delay. On the other hand, the delay of a route may be not measured at all; it may be a sum of static quantities defined for each interface along the path. Each individual delay quantity would be an estimate based on the type of link to which the interface is connected.

Reliability

Reliability measures the likelihood that the link will fail in some way and can be either variable or fixed. Examples of variable-reliability metrics are the number of times a link has failed or the number of errors it has received within a certain time period. Fixed-reliability metrics are based on known qualities of a link as determined by the network administrator. The path with highest reliability would be selected as best.

Cost

This metric is configured by a network administrator to reflect more- or less-preferred routes. Cost may be defined by any policy or link characteristic or may reflect the arbitrary judgment of the network administrator.

The term cost is often used as a generic term when speaking of route choices. For example, "RIP chooses the lowest-cost path based on hop count." Another generic term is shortest, as in "RIP chooses the shortest path based on hop count." When used in this context, either lowest-cost (or highest-cost) and shortest (or longest) merely refer to a routing protocol's view of paths based on its specific metrics.

Convergence

A dynamic routing protocol must include a set of procedures for a router to inform other routers about its directly connected networks, to receive and process the same information from other routers, and to pass along the information it receives from other routers. Further, a routing protocol must define a metric by which best paths may be determined.

A further criteria for routing protocols is that the reachability information in the route tables of all routers in the internetwork must be consistent. If router A in Figure 4.1 determines that the best path to network 192.168.5.0 is via router C and if router C determines that the best path to the same network is through router A, router A will send packets destined for 192.168.5.0 to C, C will send them back to A, A will again send them to C, and so on. This continuous circling of traffic between two or more destinations is referred to as a routing loop.

The process of bringing all route tables to a state of consistency is called convergence. The time it takes to share information across

Figure 4.2 shows an internetwork that was converged, but now a topology change has occurred. The link between the two left-most routers has failed; both routers, being directly connected, know about the failure from the data link protocol and proceed to inform their neighbors of the unavailable link. The neighbors update their route tables accordingly and inform their neighbors, and the process continues until all routers know about the change.

Figure 4.2 Reconvergence after a topology change takes time. While the internetwork is in an unconverged state, routers are susceptible to bad routing information.

Notice that at time t2 the three left-most routers know about the topology change but the three right-most routers have not yet heard the news. Those three have old information and will continue to switch packets accordingly. It is during this intermediate time, when the internetwork is in an unconverged state, that routing errors may occur. Therefore convergence time is an important factor in any routing protocol. The faster a network can reconverge after a topology change, the better.

Load Balancing

Recall from Chapter 3, "Static Routing," that load balancing is the practice of distributing traffic among multiple paths to the same destination in order to use bandwidth efficiently. As an example of the usefulness of load balancing, consider Figure 4.1 again. All the networks in Figure 4.1 are reachable from two paths. If a device on 192.168.2.0 sends a stream of packets to a device on 192.168.6.0, router A may send them all via router B or router C. In both cases, the network is 1 hop away. However, sending all packets on a single route probably is not the most efficient use of available bandwidth. Instead, load balancing should be implemented to alternate traffic between the two paths. As noted in Chapter 3, load balancing can be equal cost or unequal cost and per packet or per destination.

2. Distance Vector Routing Protocols | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020