Home > Articles > Cisco Network Technology > Network Architecture & Design > General Design Considerations for Secure Networks

General Design Considerations for Secure Networks

  • Sample Chapter is provided courtesy of Cisco Press.
  • Date: Jun 18, 2004.

Chapter Description

At the beginning of any secure network design project, many best practices apply more or less uniformly to all areas of the design. This article by Sean Convery presents these practices in a single location.

This chapter covers the following topics:

  • Physical Security Issues

  • Layer 2 Security Considerations

  • IP Addressing Design Considerations

  • ICMP Design Considerations

  • Routing Considerations

  • Transport Protocol Design Considerations

  • DoS Design Considerations

Many things difficult to design prove easy to performance. —Samuel Johnson, Rasselas: The History of Rasselas, Prince of Abissinia, 1759

A good scientist is a person with original ideas. A good engineer is a person who makes a design that works with as few original ideas as possible. There are no prima donnas in engineering. —Freeman Dyson, Physicist, Disturbing the Universe, 1979

At the beginning of any secure network design project, many best practices apply more or less uniformly to all areas of the design. This chapter presents these practices in a single location and then draws on them throughout the rest of the book. The designs presented in Chapter 13, "Edge Security Design," Chapter 14, "Campus Security Design," and Chapter 15, "Teleworker Security Design," are based on many of the concepts described here and in the companion chapters (Chapters 7–11), which detail specific design considerations for certain technologies. The topics are presented in loose compliance with the seven-layer OSI model and, as such, cover a diverse set of topics. Chapter 1, "Network Security Axioms," presented the security axioms; this chapter translates them into actionable guidance for secure network design.

Physical Security Issues

One common security truism is "Once you have physical access to a box, all bets are off." This is a good beginning assumption for this section. If an attacker has physical access to a computer, router, switch, firewall, or other device, your security options are amazingly limited. Networking devices, with few exceptions, can have their passwords reset by attaching to their console port. Hosts can be booted with a special floppy disk or CD-ROM designed to circumvent most host security on the device.

This book does not cover physical security issues in detail. Topics such as disaster recovery, site selection, and so on are not discussed at all. However, as a network designer, you must know where you are relying on physical security to augment or support your network security. There are some rules you can follow to improve your security:

  • Control physical access to facilities.

  • Control physical access to data centers.

  • Separate identity mechanisms for insecure locations.

  • Prevent password-recovery mechanisms in insecure locations.

  • Be aware of cable plant issues.

  • Be aware of electromagnetic radiation.

  • Be aware of physical PC security threats.

The rest of this section examines these seven areas.

Control Physical Access to Facilities

Effectively controlling physical access to your organization's facilities should be the single top concern for both your physical security staff and you, the network designer. Most organizations utilize one of three mechanisms to implement physical security (presented in increasing order of security):

  • Lock-and-key access

  • Key card access

  • Key card access with turnstile

Lock-and-Key Access

The most common physical security control, particularly in smaller organizations, is traditional lock-and-key access. For this method, individuals who need access to certain rooms or buildings are given keys for access. This option has the following benefits:

  • Generally, this is the cheapest option for small organizations.

  • No technical experience is required.

  • Special keys are available to thwart key duplication.

However, there are also several drawbacks:

  • If employees leave the company on less than amicable terms, they might "lose" their keys or might simply stop showing up for work. In such cases, it can be very costly to rekey the locks and redistribute keys to the valid employees.

  • Unless coupled with an alarm system that augments the lock-and-key access, there is no mechanism to determine when employees with keys access a given physical location.

  • Most keys can be easily duplicated at the local hardware store.

  • Key authentication is single-factor, meaning the key is all a person needs to access locked areas.

Key Card Access

More common in larger organizations, key card access can alleviate some of the management problems associated with lock-and-key access and can provide increased security measures. Key card access can take the form of a magnetic card reader or a smart card. All of these systems have the same basic pros and cons once you eliminate the technical differences of the technology. These are the benefits of a key card system:

  • Access to multiple locations can be controlled with a single card.

  • In the event that an employee leaves the company, the employee's card can be quickly disabled whether or not it is physically returned.

  • Locks should never need to be "rekeyed."

  • Facilities with multiple entrances are easily supported.

  • Reports can be run to show when individuals entered specific locations.

The drawbacks to a key card system are as follows:

  • Like lock-and-key access, key cards are single-factor security. Any individual with a valid key card could access the location.

  • Key card systems can be expensive, and in the event of a failure in the central authentication system, all users can be denied access to a facility.

  • The principal problem with key card access is tailgating. Tailgating is gaining unauthorized access to a building by following an individual with valid access. Oftentimes, if attackers are dressed in the appropriate clothing, they can simply follow legitimate individuals into a building without having to present a key card. Even if someone requests to see a card, an attacker can show an invalid card because it might not actually be scanned by the card reader.

Key Card Access with Turnstile

Although most often associated with ballparks and stadiums, turnstile access with a key card can be one of the most secure methods of controlling physical access to a building. For this method, a key card is used to activate the turnstile and allow one person into the building. These systems are most common in large multifloor buildings, where access can be controlled at the ground floor. In the following list, you can see that this option has all the benefits of the previous option plus more.

  • Tailgating is greatly diminished because only one person can enter per card.

  • Access to multiple locations can be controlled with a single card.

  • In the event that an employee leaves the company, the employee's card can be quickly disabled whether or not it is physically returned.

  • Locks should never need to be "rekeyed."

  • Reports can be run to show when individuals enter specific locations.

The drawbacks of a system such as this are as follows:

  • Like the previous two systems, key card access with turnstile is a single-factor identity system. Any individual with a valid card could gain access to the building.

  • This doesn't work well for facilities with multiple buildings and multiple entrances.

  • This method generally requires a security guard to verify that individuals are not hopping over the turnstile or tailgating through an entrance designed for persons with physical disabilities that bypasses the turnstile.

  • Turnstiles are not aesthetically pleasing.

  • Turnstile access can be inconvenient for employees, escorted guests, or individuals using dollies for equipment.

  • This method is more expensive than simple key card access and also has the same issues in the event of a failure in the key card authentication system.

Solving the Single-Factor Identity Problem

A second factor can be added to either of the previous key card authentication processes. The first option is to put a personal identification number (PIN) code reader at every location where there is a card reader. After using their key card, employees must enter a PIN to unlock the door. Another option is to use some form of biometric authentication. Biometric authentication could be used as either the second factor in a key card system or the principal factor in a biometric system. In the second case, users would enter a PIN after successful biometric authentication. See Chapter 4, "Network Security Technologies," for the pros and cons of biometric authentication. Both of these alternatives add cost to the system and inconvenience for users.

Control Physical Access to Data Centers

Data-center access can utilize any of the preceding mechanisms in addition to PIN-reader-only access. The important difference with data-center access is that you are often dealing with a smaller set of operators, so issues around key management are somewhat reduced.

NOTE

I once had the pleasure of experiencing a physical security audit by a client who was considering using a facility in one of my previous jobs. Needless to say, it didn't go well. One of the auditors was able to gain access to the building by tailgating. Upon entering, he asked to see the "secure" data center we had advertised. Upon reaching the entrance to the secure room, he stood on a chair and pushed up the ceiling tile outside the room. He discovered that the walls to our data center extended only 12 inches beyond the ceiling tiles, allowing access if someone climbed over them.

In the context of this discussion, data center refers to any location where centralized network resources are stored. This could include traditional data centers, wiring closets, coat closets, or someone's desk. It all depends on the size of the facility and the way it is organized.

TIP

Some ultrasecure data centers utilize sets of cameras, key card access, biometrics, and "man-traps" to catch anyone illegally trying to gain access to the room.

Separate Identity Mechanisms for Insecure Locations

Although identity design considerations are discussed in more detail in Chapter 9, "Identity Design Considerations," from a physical security perspective, it is important to ensure that passwords in physically insecure locations are not the same as those used in secure locations.

Often an organization will utilize common authentication mechanisms for the various systems that must access network resources. For example, SNMP community strings or Telnet/ SSH passwords might be set the same on all devices. From a pure security perspective, it is preferable to use two-factor authentication, when available, for each user who accesses the network device. Although this might be possible for users, it is often impossible for software management systems, which need to run scripts to make changes on several machines at once. For optimal security, different passwords should be used on each device, but this is often operationally impossible for large networks.

Therefore, at a minimum, organize your common passwords so that they are never used on systems in physically insecure locations. For example, assume you have 3 main locations (with data centers) to your organization and 10 remote sites (considered insecure). In this case, only use your shared passwords on the main sites and ensure that the passwords for each of the remote systems are unique per site at a minimum and per device ideally. As the number of insecure locations increases into the hundreds or thousands, this becomes impossible; refer to the "Business Needs" section of Chapter 2, "Security Policy and Operations Life Cycle," for guidance on calculating the costs and benefits of this and any other difficult security measure. (People generally don't compute cost/benefit on easy and cheap security measures.)

Prevent Password Recovery Mechanisms in Insecure Locations

Some devices have controls to prevent the recovery of passwords in the event that an attacker has physical access to your system. For example, on some newer Cisco routers and switches, the command is as follows:

Router(config)# no service password-recovery

When this command is entered on a router or a switch, interrupting the boot process only allows the user to reset the system to its factory default configuration. Without this command, the attacker could clear the password and have access to the original configuration. This is important because the original configuration might contain common passwords or community strings that would allow the attacker to go after other systems.

This would be particularly useful in insecure branch offices or other locations where the physical security of a network device cannot be assured.

Be Aware of Cable Plant Issues

In today's networks, there are two primary cable types: unshielded twisted pair (UTP) category 5 (or higher) and fiber optic. The risk of an attacker accessing your physical cabling is important to consider because that level of access often can bypass other security controls and provide the attacker with easy access to information (provided encryption is not used). UTP cable is very easy to tap, but it was thought years ago that fiber was immune to cable taps. We now know that this is not the case. The National Security Association (NSA) is rumored to have already tapped intercontinental network links by splicing into the cable; read about it at the following URL: http://zdnet.com.com/2100-11-529826.html.

It is also theorized that fiber cable could be bent far enough so that some light would escape if the outer layer of the cable is removed. With the right types of equipment, this information could then be read.

Additionally, if an attacker gains physical access to a wiring closet or the fiber cable as it runs in a cable tray above a drop ceiling, tapping the cable by installing couplers is another possibility.

All this being said, fiber is more secure than copper because the means to tap the signal are more expensive, difficult to execute, and often require interrupting the original flow of data to install. On the other hand, the means to tap a UTP signal can easily be purchased off of the Internet.

Be Aware of Electromagnetic Radiation

In 1985, the concerns of the paranoid among the security community were confirmed. Wim van Eck released a paper confirming that a well-resourced attacker can read the output of a cathode-ray tube (CRT) computer monitor by measuring the electromagnetic radiation (EMR) produced by the device. This isn't particularly easy to do, but it is by no means impossible. Wim's paper can be found here:

http://www.shmoo.com/tempest/emr.pdf

This form of attack is now commonly called van Eck phreaking. Additionally, in 2002, Markus Kuhn at the University of Cambridge published a similar method of reading data off of a CRT, this time by measuring the changes in the amount of light in a room. His paper can be found here:

http://www.cl.cam.ac.uk/~mgk25/ieee02-optical.pdf

And an easy-to-read FAQ on the topic can be found here:

http://www.cl.cam.ac.uk/~mgk25/emsec/optical-faq.html

A simple way to mitigate van Eck phreaking might just be to change the type of font you are using. Ross Anderson and Markus Kuhn did some excellent research on the topic:

http://www.cl.cam.ac.uk/~mgk25/ih98-tempest.pdf

I am certainly not recommending that all systems must address these sorts of security considerations, but it is good to know that such attacks are possible.

Be Aware of Physical PC Security Threats

Oftentimes, inexperienced network designers begin with an unacknowledged assumption that all the sensitive data within an organization is contained on servers. In reality, there is sensitive information about my company sitting on the laptop I am using to write this book, as well as on the servers. Like most employees at my company, server resources are used when necessary, but often interesting information is stored locally.

Several physical security issues manifest when you operate under the preceding assumption:

  • The first is that portable computer theft is a big problem, not just in the cost of replacing the computer but in the proprietary information that is stored on it. The best protection against having a lost portable computer turn into lost trade secrets is some type of file system encryption. (Some are built into modern OSs.) Chapter 4 has more details on such systems.

  • The second is that by compromising the data coming into and out of a PC, you can learn passwords, sensitive data, and so on. An attacker can achieve this through network sniffing, EMR emissions (discussed in the previous section), remote control software (Back Orifice 2000), or novel devices that attach between the keyboard and the PC and record to flash memory every key typed. For more information see this URL:

  • http://www.thinkgeek.com/stuff/gadgets/5a05.shtml

2. Layer 2 Security Considerations | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020