Home > Articles > Cisco Network Technology > Wireless/Optical/High Speed > Discovering Site-Specific Requirements for 802.11 Wireless Network Site Surveying and Installation

Discovering Site-Specific Requirements for 802.11 Wireless Network Site Surveying and Installation

  • Sample Chapter is provided courtesy of Cisco Press.
  • Date: Dec 10, 2004.

Chapter Description

This chapter outlines the physical logictics of installing a wireless network into a building. Concerns regarding the architecture and layout of the building are addressed, so that you can plan appropriately.

This chapter covers the following topics:

  • Recommended Facility Documentation

  • Limitations Affecting Equipment Installations

  • Using Cookie Cutter Designs

Often when a decision is made to install a WLAN, the decision makers do not realize that WLAN installation sites vary widely. Those who decide to move to wireless networks understand their environment and assume that most other WLAN systems and sites are much the same as theirs, and therefore the WLAN installation should be similar (and easy). Even in something as similar as a chain of retail stores, minor variations such as stock and shelving arrangements can cause coverage to vary. In reality, unless the two sites are built from the same architectural plans and populated with users and contents in a similar way, the two seemingly similar sites can be as different as night and day. Before a survey or installation is scheduled, each site needs to be evaluated separately.

This chapter addresses site-specific issues relevant to WLAN survey and installation tasks. This chapter examines topics such as site layouts, facility contents, building and construc-tions variations, different environmental conditions at the site, and other site-specific requirements. This chapter also discusses the need for accurate floor plans, building and construction specifics, an inventory of building contents, and an awareness of customer issues related to specific installation limitations.

Recommended Facility Documentation

Any engineer surveying and installing a WLAN system needs facility documentation, the collection of which should be part of the initial design stage. Facility documentation ena-bles the engineers defining the WLAN, or trying to survey and install it, to identify areas of concern, areas of coverage, user densities, and even types of antennas to consider, before ever walking onto the site. After the survey has been completed, the facility documentation becomes a critical part of the overall documentation and should be kept current as to any changes and maintained with the rest of the network documentation for future reference. The facility documentation should include (but is not to limited to) the following:

  • Site map (or floor plans)

  • Building construction details

  • Building contents inventory

  • User-area and user-density information

  • Problem-area (for WLAN) information

Site Map

Before beginning any site survey, obtain a good site map or floor plan of the site. In some cases, the site map might not really be a floor plan, but more of a site layout, including building layout and contents as well any outdoor areas that will be covered.

This site layout document will become part of the final survey and network documentation. As such, having a soft copy of this document is very helpful so that it can be copied and distributed as necessary to the survey engineers, installation team, and network support staff. Extra copies of the site map should be available to make notes on during the actual survey and installation steps, as well as during any presurvey discussions.

Prior to the survey, you can use the site map document to define desired coverage areas; identify where coverage is not needed; and define user locations and densities, problems areas, network closets, cable runs, and plenum areas. Basically, this document becomes the physical schematic of the wireless network (see Figure 8-1).

Figure 1Figure 8-1 Typical Site Map

Building Construction

Building construction can vary widely from site to site. Materials and construction techniques in San Francisco differ significantly from those used in New York City, London, or Cairo. Differences in building construction, even though sites might look similar, can cause RF to react in completely different ways. Figure 8-2 shows examples of various building materials.

Figure 2Figure 8-2 Building Materials

A multifloor building might use precast, reinforced concrete for flooring. Although this type of construction might create some attenuation problems for RF, the effect on RF penetration is significantly less than it would be with a floor of poured concrete over a steel pan. Although some RF may get through in this latter example, the steel pan provides a very good RF shield between floors (see Figure 8-3).

Walls can be similarly deceiving. In most industrial buildings, it is common to use steel studs with drywall or plasterboard over them. The drywall and plasterboard cause only a slight attenuation of RF signals, and the placement of the steel studs has little effect at all. Other walls might be concrete block, with or without steel reinforcement, which cause only limited attenuation of RF. However, precast concrete, typically using steel reinforcement, is a different story. The amount of steel used for reinforcement inside the concrete will cause the RF attenuation to vary from one building to another.

Although drywall and plaster usually minimally affect RF, the material behind the wall can pose problems. Consider a real example from a health-care facility. The RF energy was having a hard time getting into several offices. Further questioning of maintenance personnel at the facility and reviewing some older building documents revealed that this area had been remodeled recently. Before the area was used as offices, it was the radiology department. The x-ray room had been turned into offices. And, as typical with x-ray rooms, the walls were shielded to prevent x-ray energy from leaking out of the room. The walls were not removed, just covered over; therefore, the RF could not get into the offices.

Figure 3Figure 8-3 Steel-Pan Floor Construction

In some buildings, the walls might be made from a form of reinforced wire mesh, with a plaster-type material spread across it (often called stucco). The mesh can work much like an RF screen, causing a severe level of signal loss or RF attenuation.

Steel outside walls, or steel walls separating parts of a building, can detrimentally affect RF coverage (because the wall might not just restrict RF penetration, it might also create a large number of multipath signals). This is common in industrial facilities, where a building has undergone one or more additions. What was once the outside wall might now be a partition between the old and new sections of the building, causing both multipath signals and an RF shield between building sections.

Be sure to research this information before or during the survey and document your findings on the site map.

Building Contents

One often-overlooked area of concern is the building contents. Those with minimal WLAN and RF experience sometimes underestimate the effect that building contents can have on a WLAN.

Figure 8-4 shows several examples of problems that can occur in a typical office environment. Areas such as file rooms and storage rooms are often filled with steel cabinets, creating a very large RF shield for RF entering that room, or even passing through it to other areas of the facility. Although most would assume an area filled with cubicles should have minimal effect on RF, it might in fact create a challenge for RF coverage. The number of cubical partitions, the amount of steel in the partitions and desks, and the size and make-up of the bookshelves can affect RF range.

Figure 4Figure 8-4 Office Issues

Another area that is very difficult to cover is a library or documentation area. Shelves full of books are shelves full of paper, and most paper has a high level of attenuation to WLAN frequencies. It is very common for WLANs to use directional antennas, focusing the RF energy down the aisles of the books. (See Figure 8-5.) Because of similar shelving, ware-houses and even some retail stores also use directional antennas in this way.

Figure 5Figure 8-5 Directional Antennas for Library Coverage

Kitchens and break-rooms usually contain microwave ovens. Microwaves are also found around many health-care and industrial facilities for purposes other than heating food. Although microwaves pose no problems for 5-GHz WLANs, they can be problematic for 2.4-GHz WLANs. The typical microwave oven uses the same frequencies as a 2.4-GHz WLAN. (This is because 2.4 GHz is the resonant frequency of water, and when 2.4-GHz energy strikes water molecules, it is absorbs the energy and causes the molecules to vibrate, creating friction and heat.) Locating a 2.4-GHz access point (AP) close to a microwave can cause undue interference and result in poor RF communications. Take care to keep these APs (and clients when possible) at least 10 feet away from any standard microwave oven. It is therefore recommended to note the location of any such devices on the site map. Also be aware that industrial microwave ovens sometimes have a much higher power than those found in the home or office, possibly creating even more interference. Testing should in-clude RF coverage verification while any microwaves in the local vicinity are in full operation.

In one case, a health-care facility was having trouble with one particular AP that was dropping all associations intermittently. Close inspection of the facility turned up a microwave oven in an area that was not part of the RF-covered area, but was located in a lab adjacent to the AP-covered area. The problem was that the oven was located on the other side of the wall (made from drywall) from the AP, with a total of about 5 feet (and two pieces of drywall) separation. This is why it is important to understand the entire site, including areas where coverage may not be needed. Figure 8-6 shows a site map with potential problem areas labeled.

Figure 6Figure 8-6 Hidden Site Problems

Locations such as emergency rooms and cardiac care in hospitals use sensitive equipment such as electrocardiographs (EKGs) and other monitoring systems. Although these devices are not generally a problem with WLANs, take care to locate the radio gear near the devices and to verify that the RF in the area does not cause any interference. One common problem occurs with older plotters and printers. The RF energy can cause slight variations in the print and plotter driver mechanisms, resulting in "glitches" in the patient printouts.

As discussed in Chapter 6, "Preparing for a Site Survey," all cordless and wireless devices should be inventoried. Phones, speaker, cameras, cordless mice, cordless keyboards, baby monitors, and virtually anything that might be RF related should be noted.

In a warehouse, retail environment, or even an office building, a change of contents can greatly affect the coverage of an AP. Inventory levels often change in a warehouse or retail facility. At certain times of the year (such as early November, when stock levels rise for the holiday shopping season), stock levels in some facilities may reach beyond 100 percent, with material placed in any possible free space, such as directly in front of the AP that provides coverage to the area. This poses a real problem for the survey engineer who is trying to survey when the stock level might be at a low level corresponding to the season. (Many installations occur during the off-season, when facilities are not running at peak capacity.)

Defined User Areas and Densities

The topic of user density has been brought up many times in this book. As stressed prev-iously, defining user areas and densities is a crucial part of the design and must be on the minds of design engineers and survey engineers at all times. The overall performance of the WLAN system depends on proper user density.

There have been surveys based on nothing but user density. At one very large software company, the buildings were all built in a very similar manner, and with identical internal design and contents. All cubicles were identical, all office construction was identical, and the number of users in a given area was very similar.

For this customer, it was decided that the applications used by nonengineering employees would permit between 20 and 25 users per AP. This provided adequate performance for normal operational network load. The engineers, however, required a bit more perform-ance, and the user density was lowered to between 10 and 15 users per AP.

Based on information such as this, some of the design can be done up front. You can use the site map to determine how large the cell coverage needs to be. For example, a survey determined that a single AP set to default power levels, with dipole antennas, could provide coverage for many more users (based on their seating locations) than the design calls for. In this particular case, the desired coverage turned out to be a small circle on the site map, and was about the size of a coffee cup. From this point, it was a matter of defining how many "coffee cups" were needed (see Figure 8-7). The engineers then selected the power setting to provide the proper coverage for the user density in the appropriate areas. Finally, testing was completed to prove the guesstimations of the coffee cup survey.

Figure 7Figure 8-7 Coffee Cup Layout

If voice is to be used over the WLAN, it is vital to the design to understand the capacity of the AP versus the number of calls that can be carried by one AP at any given time. Typically, a standard 802.11b AP supports only between six and eight calls with the standard com-pression used in 802.11 voice over IP (VoIP) phones. As compression techniques improve, or as the wireless 802.11 VoIP phones move to support 802.11g or 802.11a, the number of calls per AP will increase.

2. Limitations Affecting Equipment Installations | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020