Home > Articles > Storage Networking Fundamentals: Storage Devices

Storage Networking Fundamentals: Storage Devices

  • Sample Chapter is provided courtesy of Cisco Press.
  • Date: Mar 4, 2005.

Contents

  1. Disk Drives
  2. Tape Drives
  3. Summary
  4. Q & A

Chapter Description

This chapter examines the pros and cons of various storage devices to help you decide which storage devices are appropriate for your storage network.

Upon completing this chapter, you will be able to

  • Participate in discussions with vendors, work colleagues, and other professionals about the advantages and disadvantages of disk drive implementations being used in or planned for storage networks

  • Analyze and compare the specifications and capabilities of different disk drives and their suitability for different types of applications

  • Discuss and plan deployments of tape drives for storage networks

Storage devices perform the fundamental function of storage networks, which is the reading and writing of data stored on nonvolatile media. They operate in the microscopic realm, combining advanced magnetic physics, chemistry, and electronics. Demands to increase capacity and performance continue to force the industry to conduct fundamental scientific research on the microscopic characteristics of materials.

Storage devices are the building blocks of storage in disk subsystems as well as being used as standalone products in server systems. This chapter mostly examines disk drive technology as the device that is used far more than any other. Tape drives are looked at at the end of the chapter.

Disk Drives

Several types of storage devices are used in storage networking, but by far the most important is the disk drive. If Harry Truman worked in the storage network industry, he would have said the buck stops at the disk drive. By now we have almost come to take disk drives for granted as ubiquitous gadgets that are readily available at volume discounts. The fact is, disk drive technology is as impressive as any other technology in all of IT, with amazing capabilities and physical characteristics.

In the sections that follow, we'll examine the various subassemblies that make up a disk drive, discuss the strengths and limitations of these amazing machines, and point out what they mean for storage network applications.

Major Parts of a Disk Drive

Disk drives are constructed from several highly specialized parts and subassemblies designed to optimally perform a very narrowly defined function within the disk drive. These components are

  • Disk platters

  • Read and write heads

  • Read/write channel

  • Arms and actuators

  • Drive spindle motor and servo control electronics

  • Buffer memory

  • Disk controller

Now we'll discuss each of these subassemblies briefly.

Disk Platters

The physical media where data is stored in a disk drive is called a platter. Disk platters are rigid, thin circles that spin under the power of the drive spindle motor. Platters are built out of three basic layers:

  • The substrate, which gives the platter its rigid form

  • The magnetic layer, where data is stored

  • A protective overcoat layer that helps minimize damage to the disk drive from microscopically sized dust particles

The three different layers within a disk platter are illustrated in Figure 4-1, which shows both the top and bottom sides of a platter.

Figure 1Figure 4-1 Material Layers in a Disk Media Platter

Substrates are made from a variety of materials, including aluminum/magnesium alloys, glass, and ceramic materials. Considering the microscopic nature of disk recording and how close the heads are to the surface, they must be amazingly flat and relatively inelastic to thermal expansion and contraction. In addition, they have to be almost completely uniform in density and free from material defects that could result in balance imperfections, which cause vibration and friction (heat) problems when spinning at high revolutions per minute (rpm).

The magnetic layer in most disk drives today uses thin film technology, which is very smooth and only a few millionths of an inch in thickness. The thin film layer is made by spraying vapor molecules of the magnetic materials on the surface of the substrate. The magnetic characteristics of the magnetic materials give the platter its areal density—the measurement of how many bits can be written per square inch.

The protective overcoat layer provides protection from microscopic elements such as dust and water vapor, as well as from disk head crashes. Considering the physics involved in high-speed disk drives, this coating is necessarily thin and provides, at best, light-duty protection. The best way to protect disk drive platters is to operate them in clean, dust-free, temperature-controlled environments.

Storage capacity of a single platter varies from drive to drive, but recent developments in commercially available products have resulted in platter capacities in excess of 100 GB per platter.

Disk drives are usually made by arranging multiple platters on top of each other in a stack where the platters are separated by spacers to allow the disk arms and heads to access both sides of the platters, as shown in Figure 4-2.

Figure 2Figure 4-2 Disk Platters Connected to the Spindle Motor in a Stack

Read and Write Heads

The recording heads used for transmitting data to and from the platter are called read and write heads. Read/write heads are responsible for recording and playing back data stored on the magnetic layer of disk platters. When writing, they induce magnetic signals to be imprinted on the magnetic molecules in the media, and when reading, they detect the presence of those signals.

The performance and capacity characteristics of disk drives depend heavily on the technology used in the heads. Disk heads in most drives today implement giant magnetoresistive (GMR) technology, which uses the detection of resistance variances within the magnetic layer to read data. GMR recording is based on writing very low-strength signals to accommodate high areal density. This also impacts the height at which the heads "fly" over the platter.

The distance between the platter and the heads is called the flying height, or head gap, and is measured at approximately 15 nanometers in most drives today. This is much smaller than the diameter of most microscopic dust particles. Considering that head gap tolerances are so incredibly close, it is obviously a good idea to provide a clean and stable environment for the tens, hundreds, or thousands of disk drives that are running in a server room or data center. Disk drives can run in a wide variety of environments, but the reliability numbers improve with the air quality: in other words, relatively cool and free from humidity and airborne contaminants.

The reference to "flying" with disk heads comes from the aerodynamic physics at work in disk drives: air movement caused by the rapidly spinning platters passes over the heads, providing lift to the heads in much the same way airplane wings are lifted by the difference in air pressure above and below them.

Read/Write Channel

While we tend to think about data purely in the digital realm, the physical recording is an analog signal. Somehow, the 0s and 1s of digital logic have to be converted to something that makes an impression on magnetic media. In other words, data on disk does not resemble written language at all but is expressed by the pattern of a magnetic signal on moving media. The read/write channel is the disk drive subassembly that provides a specialized digital/analog conversion.

The read/write channel is implemented in small high-speed integrated circuits that utilize sophisticated signal processing techniques and signal amplifiers. The magnetoresistive phenomenon that is detected by the read heads is very faint and requires significant amplification. Readers might find it interesting to ponder how data read from disk is not actually based on detecting the magnetic signal that was written to media. Instead, it is done by detecting minute differences in the electrical resistance of the media, caused by the presence of different magnetic signals. Amazingly, the resistance is somehow detected by a microscopically thin head that does not make contact with the media but floats over it at very high speeds.

Arms and Actuators

The read and write heads have to be precisely positioned over specific tracks. As heads are very small, they are connected to disk arms that are thin, rigid, triangular pieces of lightweight alloys. Like everything else inside a disk drive, the disk arms are made with microscopic precision so that the read/write heads can be precisely positioned next to the platters quickly and accurately.

The disk arms are connected at the base to the drive actuator, which is responsible for positioning the arms. The actuator's movements are controlled by voice-coil drivers; the name is derived from voice coil technology used to make audio speakers. Considering that some speakers have to vibrate at very high frequencies to reproduce sounds, it's easy to see how disk actuators can be designed with voice coils to move very quickly. The clicking sounds you sometimes hear in a disk drive are the sounds of the actuator being moved back and forth.

Drive Spindle Motor and Servo Control Electronics

The drive platters rotate under power of the drive spindle motor, which is designed to maintain constant speeds with minimal vibration over long periods of time, sometimes measured in the tens of thousands of hours.

Most drive failures are related to motor failures. This is not to say the motors are poorly designed or designed to fail, because they clearly are not. However, they are always moving toward higher speeds with less power consumption and less noise, and the tolerances are thin.

The actual spindle that the platters connect to is directly fixed to the motor's drive shaft. The spindle looks a bit like the inner core of some old 45-rpm record players, except the platters do not drop or slide over the core, but are fixed in place. Separator rings are used to space the platters precisely so their surfaces can be traversed by the disk arms and heads accurately.

Among the many parts of a disk drive, the bearings in the motor see constant wear and tear. While many other things can make a disk drive fail, it is inevitable that the bearings will eventually wear out.

The speed of the spindle motor must be constantly monitored to make sure it remains consistent hour after hour, day after day, month after month. The type of technology used to maintain constant speed is called a servo-controlled closed loop, and it is used for many different applications to fine-tune automated systems. Disk drives are designed with sophisticated feedback control circuits that detect minute speed variations in the rotating platter by reading tracking and timing data on the disk. If the speed varies too far one way or another, the servo feedback circuit slightly changes the voltage supplied to the spindle motor to counteract the change.

Buffer Memory

The mechanical nature of reading and writing data on rotating platters limits the performance of disk drives to approximately three orders of magnitude (1000 times) less than the performance of data transfers to memory chips. For that reason, disk drives have internal buffer memory to accelerate data transmissions between the drive and the storage controller using it.

Buffer memory might not have a significant performance impact for a single disk drive system, such as a desktop or laptop system, but buffer memory can make a big difference in storage subsystems that support high-throughout applications. When multiple drives are assembled together in an array, the controller, such as a subsystem controller, can overlap I/Os across multiple drives, using buffer memory transfers whenever possible. The drive can make internal transfers of data between buffer memory and its media platters while the subsystem controller is working with another drive. In general, buffer memory in disk drives can improve I/O performance for applications that read and write small chunks of randomly accessed data. Alternatively, streaming applications with large files stored in contiguous storage locations do not realize many benefits from buffer memory.

Buffer memory sizes have increased over time, although not at the same rate as the areal density of platters. Today, disk drives typically have buffer capacities between 2 MB and 16 MB.

Disk Controller

Disk drives all have internal target controllers that respond to commands from host or subsystem initiators. In addition to interoperating with the external initiator, the storage controller in a disk drive is responsible for executing the command within the drive. The software component of a disk drive controller is referred to as firmware and is typically stored in e-prom chips in the drive's circuit board.

Processor chips used as disk drive controllers are constantly being improved with faster cores and more memory. Strangely enough, one of the challenges for disk drive manufacturers is how to make the best use of the additional intelligence at their disposal. It's a tougher question than it first appears because disk drives have traditionally been used as relatively stupid slave devices responding to I/O requests from host and subsystem controllers. Storage applications such as NAS can be added to disk drives, but that creates competition between the disk drive manufacturers and their customers—the system and subsystem vendors. So far, the disk drive manufacturers have been at the wrong end of the pecking order and their attempts to integrate higher-level storage functions in the drives have mostly failed.

Instead, what has been successful is the use of processor intelligence to increase reliability and ease of use. If you stop to consider how much easier it is to install disk drives today than it was ten years ago, the improvement has been remarkable. When you think about these improvements in terms of installed capacity, the advancements have been truly incredible. For example, the reliability provided by a handful of today's high-capacity disk drives used together to form a terabyte (TB) of storage is far, far better than the reliability of the approximately 500 disk drives that were needed ten years ago to build the same terabyte of capacity. Obviously, improvements in areal density make this possible, but a significant amount of work has also been done in the drive's internal controllers.

Data Structures on Disk Drives

The mechanisms of disk drive technology are only half of the story; the other half is the way data is structured on the disk. There is no way to plan for optimal storage configurations without understanding how data is structured on the surface of disk drive platters. This section discusses the following data structures used in disk drives:

  • Tracks, sectors, and cylinders

  • Disk partitions

  • Logical block addressing

  • Geometry of disk drives and zoned-bit recording

Tracks, Sectors, and Cylinders

Disk platters are formatted in a system of concentric circles, or rings, called tracks. Within each track are sectors, which subdivide the circle into a system of arcs, each formatted to hold the same amount of data—typically 512 bytes. Once upon a time, the block size of file systems was coupled with the sector size of a disk. Today the block size of a file system can range considerably, but it is usually some multiple of 512 bytes.

Cylinders are the system of identical tracks on multiple platters within the drive. The multiple arms of a drive move together in lockstep, positioning the heads in the same relative location on all platters simultaneously.

The complete system of cylinders, tracks, and sectors is shown in Figure 4-3.

Disk Partitions

Disk partitions divide the capacity of physical disk drives into logical containers. A disk drive can have one or more partitions, providing a way for users to flexibly create different virtual disks that can be used for different purposes.

For instance, a system could have different partitions to reserve storage capacity for different users of the system or for different applications. A common reason for using multiple partitions is to store data for operating systems or file systems. Machines that are capable of running two different operating systems, such as Linux and Windows, could have their respective data on different disk partitions.

Disk partitions are created as a contiguous collection of tracks and cylinders. Visually, you can imagine partitions looking like the concentric rings of an archery target with the bull's-eye being replaced by the disk motor's spindle. Partitions are established starting at the outer edge of the platters and working toward the center. For instance, if a disk has three partitions, numbered 0, 1, and 2, partition 0 would be on the outside and partition 2 would be closest to the center.

Figure 3Figure 4-3 Cylinders, Tracks, and Sectors in a Disk Drive

Logical Block Addressing

While the internal system of cylinders, tracks, and sectors is interesting, it is also not used much anymore by the systems and subsystems that use disk drives. Cylinder, track, and sector addresses have been replaced by a method called logical block addressing (LBA), which makes disks much easier to work with by presenting a single flat address space. To a large degree, logical block addressing facilitates the flexibility of storage networks by allowing many different types of disk drives to be integrated more easily in a large heterogeneous storage environment.

With logical block addressing, the disk drive controller maintains the complete mapping of the location of all tracks, sectors, and blocks in the disk drive. There is no way for an external entity like an operating system or subsystem controller to know which sector its data is being placed in by the disk drive. At first glance this might seem risky—letting a tiny chip in a disk drive be responsible for such an important function. But, in fact, it increases reliability by allowing the disk drive to remap sectors that have failed or might be headed in that direction.

Considering the areal density and the microscopic nature of disk recording, there are always going to be bad sectors on any disk drive manufactured. Disk manufacturers compensate for this by reserving spare sectors for remapping other sectors that go bad. Because manufacturers anticipate the need for spare sectors, the physical capacity of a disk drive always exceeds the logical, usable capacity. Reserving spare sectors for remapping bad sectors is an important, reliability-boosting by-product of LBA technology. Disk drives can be manufactured with spare sectors placed throughout the platter's surface that minimize the performance hit of seeking to remapped sectors.

Geometry of Disk Drives and Zoned-Bit Recording

There is no way to escape radial geometry when working with disk drives. One of the more interesting aspects of this radial geometry is that the amount of recording material in a track increases as you move away from the center of the disk platter. Disk drive tracks can be thought of as media rings having a circumference that is determined by the mathematical expression 2pr, where r is the radius for the track. The amount of recording material in a track is determined by radial length. This means that the outermost tracks can hold more data than the inside tracks. In fact, they can hold a lot more data than inside tracks.

To take advantage of this geometry, disk drive designers developed zoned-bit recording, which places more sectors inside tracks as the radius increases. The general idea is to segment the drive into "sector/track density" zones, where the tracks within that zone all have the same number of sectors. The outermost zone, zone 0, has the most sectors per track, while the innermost zone has the fewest.

Logical block addressing facilitates the use of zoned-bit recording by allowing disk drive manufacturers to establish whatever zones they want to without worrying about the impact on host/subsystem controller logic and operations. As platters are never exchanged between disk drives, there is no need to worry about standardized zone configurations.

Table 4-1 shows the zones for a hypothetical disk drive with 13 zones. The number of tracks in a zone indicates the relative physical area of the zone. Notice how the media transfer rates change as the zones move closer to the spindle. This is why the first partitions created on disk drives tend to have better performance characteristics than partitions that are located closer to the center of the drive.

Table 4-1 Disk Drive Zones

Zone

Number of Tracks

Sectors in Each Track

Media Transfer Rate in Mbps

0

1700

2140

1000

1

3845

2105

990

2

4535

2050

965

3

4365

2000

940

4

7430

1945

915

5

7775

1835

860

6

5140

1780

835

7

6435

1700

800

8

8985

1620

760

9

11,965

1460

685

10

12,225

1295

610

11

5920

1190

560

12

4320

1135

530


Disk Drive Specifications

Disk drive specifications can be confusing and difficult to interpret. This section highlights some of the most important specs used with disk drives in storage networking applications, including the following:

  • Mean time between failures

  • Rotational speed and latency

  • Average seek time

  • Media transfer rate

  • Sustained transfer rate

Mean Time Between Failures

Mean time between failure (MTBF) indicates the expected reliability of disk drives. MTBF specifications are derived using well-defined statistical methods and tests run on a large number of disk drives over a relatively short period of time. The results are extrapolated and are expressed as a very large number of hours—usually in the range of 500,000 to 1.25 million hours. These numbers are unthinkably high for individual disk drives—1.25 million hours is approximately 135 years.

MTBF specifications help create expectations for how often disk drive failures will occur when there are many drives in an environment. Using the MTBF specification of 1.25 million hours (135 years), if you have 135 disk drives, you can expect to experience a drive failure once a year. In a storage network environment with a large number of disk drives—for instance, over 1000 drives—it's easy to see that spare drives should be available because there will almost certainly be drive failures that need to be managed. This also underlines the importance of using disk device redundancy techniques, such as mirroring or RAID.

Rotational Speed and Latency

One of the most common ways to describe the capabilities of any disk drive is to state its rotational speed in rpm. The faster a disk drive spins, the faster data can be written to and read from the disk's media. The performance differences can be enormous. All other things being equal, a 15,000-rpm disk drive can do more than twice the amount of work as a 7200-rpm disk drive. If 50 or more disk drives are being used by a transaction processing system, it's easy to see why somebody would want to use higher-speed drives.

Related to rotation speed is a specification called rotational latency. After the drive's heads are located over the proper track in a disk drive platter, they must wait for the proper sector to pass underneath before the data transfer can be made. The time spent waiting for the right sector is called the rotational latency and is directly linked to the rotational speed of the disk drive. Essentially, rotational latency is given as the average amount of time to wait for any random I/O operation and is calculated as the time it takes for a platter to complete a half-revolution.

Rotational latencies are on the range of 2 to 6 milliseconds. This might not seem like a very long time. But it is very slow compared to processor and memory device speeds. Applications that tend to suffer from I/O bottlenecks such as transaction processing, data warehousing, and multimedia streaming require disk drives with high rotation speeds and sizable buffers.

Table 4-2 shows the rotational latency for several common rotational speeds.

Table 4-2 The Inverse Relationship Between Rotational Speed and Rotational Latency in Disk Drives

Rotational Speed

Rotational Latency (in ms)

5400

5.6

7200

4.2

10000

3.0

12000

2.5

15000

2.0


Average Seek Time

Along with rotational speed, seek time is the most important performance specification for a disk drive. Seek time measures the time it takes the actuator to reposition the read/write heads from one track to another over a platter. Average seek times represent a performance average over many I/O operations and are relatively similar to rotational latency—in the range of 4 to 8 milliseconds.

Transaction processing and other database applications that perform large numbers of random I/O operations in quick succession require disk drives with minimal seek times. Although it is possible to spread the workload over many drives, transaction application performance also depends significantly on the ability of an individual disk drive to process an I/O operation quickly. This translates into a combination of low seek times and high rotational speeds.

Media Transfer Rate

The media transfer rate of a disk drive measures the performance of bit read/write operations on drive platters. Unlike most storage specifications, which are listed in terms of bytes, the media transfer rate is given in terms of bits. The media transfer rate measures read/write performance on a single track, which depends on the radial length the track is positioned at. In other words, tracks in zone 0 have the fastest media transfer rates in the disk drive. For that reason, media transfer rate specifications are sometimes given using ranges.

Sustained Transfer Rate

Most I/O operations on a disk drive work across multiple tracks and cylinders, which involves the ability to change the location of the read/write heads. The sustained transfer rate specification takes into account the physical delays of seek time and rotational latency and is much closer to measuring actual user data performance than the media transfer rate.

That said, sustained transfer rates indicate optimal conditions that are difficult to approach with actual applications. There are other important variables such as the size of the average data object and the level of fragmentation in the file system. Nonetheless, sustained transfer rate is a pretty good indication of a drive's overall performance capabilities.

Optimizing Disk Drive Performance in Storage Networks

Given that disk drives are relatively slow, people have developed several methods and techniques to increase their performance. The performance enhancements discussed in this section include

  • Limiting drive contention

  • Short-stroking the drive

  • Matching rotation speeds

  • Aligning zones

Limiting Drive Contention

Multiple applications that are actively performing I/O operations on a single disk drive can generate a significant amount of seek time and rotation latency, causing performance to deteriorate. Therefore, it makes sense to understand which applications are accessing each disk drive in order to avoid contention for a drive's slow mechanical resources.

Disk bottlenecks can occur in storage area networking (SAN) environments where many disk drives provide storage to many systems and applications. Without good planning, it's possible for different partitions on a single disk drive to be assigned to different applications requiring higher I/O performance levels. In that case, the two applications would wind up competing for the use of a single actuator and a single rotating spindle.

One of the best ways to limit contention for a disk drive is to limit the number of partitions it has. For example, administrators could configure some percentage of high-speed drives to have two partitions—one for a high-performance application and the other for a lower-performance application. Unfortunately, the enforcement of this objective would have to be a manual task, as the technology for automating it is not yet available. A facility that allowed automated disk partition policies to be applied to drives might be very useful. The intelligence to do it is in the drive, but the requirement to provide it is not yet obvious to disk drive manufacturers.

NOTE

Most applications have minimal storage I/O requirements and place a minimal load on disk drives. These "I/O-lite" applications probably don't need to be monitored for disk drive contention problems. These applications also do not deserve to hog the best parts of high-speed disk drives. Most administrators are not used to creating partitions and letting them sit idle, but that could be done to reserve a percentage of the "choicest cuts" of some drives in case they are needed by a high-performance application in the future. The question is, if an application does not require optimal I/O performance, why allocate a high-performance disk partition to it?

Short-Stroking the Drive

A technique known as short-stroking a disk limits the drive's capacity by using a subset of the available tracks, typically the drive's outer tracks. This accomplishes two things: it reduces seek time by limiting the actuator's range of motion, and it increases the media transfer rate by using the outer tracks, which have the highest densities of data per track.

Short-stroking is normally done by establishing a single partition on a drive that uses some subset of the total capacity. For instance, you can establish an 80-GB partition on a 200-GB disk drive to increase performance.

Matching Rotation Speeds

There is a tendency in storage networking to treat all storage address spaces equally, which makes them easier to manage. This approach is likely to work very well for the majority of applications, but it falls short for those applications that need the highest performance.

An obvious difference between disk drives is their rotational speed. It would not be a good idea to match slow-speed drives with high-speed drives in support of a high-throughput transaction processing application.

The same concept applies to drive buffer memory. You would not want to use drives with insufficient buffer capacity, slowing down an otherwise fast configuration.

Aligning Zones

The performance differences across different zones on disk drives could be significant for certain applications that expect consistently high I/O rates, such as data warehousing processing. For example, a disk partition on the outside of a disk might have almost twice the performance of a partition on the inside of a disk. In effect, this is the same situation as wanting to match the rotational speeds of disk drives used for high-performance applications, except this variable adds the element of matching the zones or the relative position of the partitions on a drive.

2. Tape Drives | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020