Home > Articles > Cisco Network Technology > IP Communications/VoIP > Basic IP Connectivity and Troubleshooting in Cisco Express Forwarding

Basic IP Connectivity and Troubleshooting in Cisco Express Forwarding

  • Sample Chapter is provided courtesy of Cisco Press.
  • Date: Oct 26, 2007.

Chapter Description

This chapter presents the general troubleshooting used on Cisco IOS routers and switches as a first step in troubleshooting IP connectivity problems. It helps you verify whether CEF is the root cause of a particular IP connectivity problem.

From the Book

Cisco Express Forwarding

Cisco Express Forwarding

$65.00

This chapter covers the following topics:

  • Troubleshooting IP connectivity
  • Troubleshooting punt adjacencies
  • Understanding CEF error messages
  • Troubleshooting commands reference

Cisco Express Forwarding (CEF) troubleshooting can be tedious, laborious, and difficult. However, most instances of CEF troubleshooting do not require detailed Cisco IOS architecture and platform (hardware) architecture knowledge. For example, many CEF issues are found in two or three steps of troubleshooting. In addition, many issues that appear to be CEF-related end up being a result of a misconfiguration or inoperable end device.

The first section of this chapter presents the general troubleshooting used on Cisco IOS routers and switches as a first step in troubleshooting IP connectivity problems. CEF occasionally is the scapegoat for IP connectivity problems, and this chapter helps you verify whether CEF is the root cause of a particular IP connectivity problem.

This chapter does not delve into platform specifics of troubleshooting CEF. The chapter simply approaches troubleshooting from a CEF software-switching and command-line interface (CLI) perspective. Most mid- to high-end routers and all Catalyst switches support distributed CEF (dCEF), or hardware switching.

This chapter begins the CEF troubleshooting for all Cisco platforms, including the Cisco 2600, 3700, 7500, 12000, and Catalyst 6500. Chapter 5, "Understanding Packet Switching on the Cisco Catalyst 6500 Supervisor 720," goes into further detail for additional platform and hardware troubleshooting of CEF for the Cisco Catalyst 6500.

The chapter concludes with a table of the basic CEF troubleshooting commands.

Troubleshooting IP Connectivity

As mentioned in the introduction, CEF is a common scapegoat for IP connectivity issues. As such, when approaching an IP connectivity issue, keep an open mind about the root cause of the issue.

This section reviews the methodology for troubleshooting IP connectivity issues, which leads to identifying and troubleshooting CEF issues.

The best approach in troubleshooting is to build a troubleshooting plan. Flow charts simplify troubleshooting because they present a stepwise approach to troubleshooting. The following list briefly outlines the first steps in troubleshooting IP connectivity issues and Cisco IOS CEF:

  • Step 1 Accurately describe the problem.
  • Step 2 Scope the network topology.
  • Step 3 Review the Open Systems Interconnection (OSI) model.
    • (a)Verify the physical layer.
    • (b)Verify the Layer 2 layer topology.
  • Step 4 Verify the Address Resolution Protocol (ARP) table.
  • Step 5 Verify the IP routing table.
  • Step 6 Verify the CEF Forwarding Information Base (FIB) table.
  • Step 7 Verify the adjacency table.
  • Step 8 Conduct hardware-specific troubleshooting.

Accurately Describe the Problem

Accurately articulating your IP connectivity problem is paramount to troubleshooting effectively. An ad hoc approach to troubleshooting is usually ineffective in resolving problems. For example, you do not go to your dentist and tell him you are in pain without describing the symptoms, such as which tooth, how often, how intense, how widespread, what causes the pain, and so on. The same premise exists with IP connectivity troubleshooting. To help yourself, you need to know as much about the issue as possible.

The following questions aid you in accurately articulating your IP connectivity problem:

  • Is your IP connectivity problem isolated to a single end device or multiple end devices?

  • Is your IP connectivity problem isolated to a single router or Ethernet switch?

  • Does your IP connectivity problem exist only on end devices, or does it affect the management CLI of routers and switches as well?

  • How widespread is the problem?

  • Is the problem widespread or localized to specific area of your network topology?

  • Is the problem intermittent or consistent? For example, using the Internet Control Message Protocol (ICMP) ping utility in Cisco IOS and on end devices, are you getting intermittent responses to ICMP echo requests such as every other response, no responses, or inconsistent responses (one out of ten)?

  • Does this issue depend on packet size? If you send ICMP echo requests at different sizes, do you consistently get all your responses or does the problem vary with packet size?

  • When did the problem first occur? Were there any changes to the network at the same time the problem started occurring?

These questions aid you in articulating your IP connectivity issues. The next section describes an important next step, building the network topology.

Scoping the Network Topology

It is nearly impossible to troubleshoot any type of CEF issue or network connectivity issue without a network diagram that depicts IP addresses, IP routes, devices such as firewalls and switches, and so on. Troubleshooting IP connectivity problems without the aid of a visual topology is nearly impossible unless you can localize the issue to a specific router or switch. In large IP routing scenarios, a network topology is required to troubleshoot connectivity problems. Generally, both logical and physical topologies aid in troubleshooting. Figure 4-1 illustrates a sample physical topology.

Figure 4-1

Figure 4-1 Sample Network Topology

Reviewing the OSI Model for Troubleshooting

The next step in troubleshooting any IP connectivity issue is to review the OSI model and verify that your issue is indeed a Layer 3 (network) issue. Figure 4-2 briefly reviews the OSI model. As a reader of this high-level technology book on CEF, we assume you have an understanding of the OSI model.

Figure 4-2

Figure 4-2 OSI Model

The following sections start from the bottom of the OSI model and review troubleshooting physical connectivity and Layer 2 issues that can affect IP connectivity and give the appearance of a CEF issue.

Troubleshooting Physical Connectivity

An IP connectivity issue might simply be a Layer 1 (physical layer) problem. For example, if you are unable to ping a network device through a router, do not assume that you are having a CEF issue. First, ensure that the host is connected and verify that the physical layer between the host and destination is not sustaining errors. Example 4-1 illustrates sample output from a show interfaces command in Cisco IOS.

Example 4-1. Verifying the Physical Layer

Switch#show interfaces GigabitEthernet 3/6
GigabitEthernet3/6 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet Port, address is 0010.7bfa.808d (bia 0010.7bfa.808d)
  MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseSX
  input flow-control is on, output flow-control is off
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:22, output never, output hang never
  Last clearing of "show interface" counters 5w0d
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 2000 bits/sec, 2 packets/sec
     683355349 packets input, 357724908540 bytes, 0 no buffer
     Received 155022 broadcasts (155022 multicast)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     338647150 packets output, 23295655000 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

In regard to the show interfaces command and verifying physical connectivity, verify that your ingress and egress interfaces are not sustaining errors such as input errors, cyclic redundancy check (CRC) errors, output errors, excessive collisions, overruns, late collisions, or output buffer failures. These types of errors can lead to intermittent or total loss of IP connectivity. Generally, physical layer issues cause intermittent connectivity if the connection has link. Layer 1 errors can be a result of a bad cable, bad port, faulty hardware, and so on. Before proceeding with IP connectivity troubleshooting and ultimately CEF troubleshooting, you must rule out Layer 1 issues.

Troubleshooting Layer 2 Issues

The next step in troubleshooting intermittent connectivity, after physical layer (Layer 1) issues have been ruled out, is to verify that the Layer 2 topology is operating correctly. Verifying the Layer 2 topology includes, but is not limited to, verifying the spanning-tree topology, MAC address table, and Hot Standby Routing Protocol (HSRP) status in switched networks. In a point-to-point router configuration, these features are seldom used. Nevertheless, if your topology involves aggregating and connecting routers to Ethernet switches, you must check the Layer 2 topology before assuming that CEF is the root cause of an IP connectivity issue. Because CEF is found on all Layer 3 Cisco Catalyst switches, troubleshooting Layer 2 issues is necessary when troubleshooting IP connectivity issues on these platforms.

The following list articulates the most common Layer 2 features that can affect IP connectivity when not operating in a correct state:

  • 802.1D, 802.1w, and 802.1s Spanning Tree Protocols
  • Hot Standby Routing Protocol (HSRP)
  • Virtual Router Redundancy Protocol (VRRP)
  • EtherChanneling (port channeling)
  • Compression (software- or hardware-based)
  • Encryption (software- or hardware-based)
  • Firewalls
  • Virtual Private LAN Services (VPLS)
  • Any Transport over Multiprotocol Label Switching (AToM)

Consult the list for applicable features in your network topology and refer to the Cisco.com website for more details on troubleshooting these features. Troubleshooting these features is outside the scope of this book.

Because many Cisco IOS router experts are not also Cisco IOS switch experts, router experts can find switch troubleshooting daunting. Nevertheless, you should rule out Layer 2 issues as a cause for IP connectivity and CEF issues. The most efficient way to troubleshooting Layer 2 issues is to remove redundant paths, disable as many features as possible, and isolate connectivity issues to a single host.

After the mundane Layer 1 and Layer 2 issues have been ruled out, you can finally transition to troubleshooting IP and CEF, the main focus of this book. As with any troubleshooting, you use a stepwise approach.

Verifying the ARP Table

The first step in troubleshooting IP connectivity issues and CEF from a Layer 3 perspective is to consult the ARP table for identified IP devices that are experiencing connectivity issues. When CEF cannot locate a valid adjacency for a destination prefix, it punts the packets to the CPU for ARP resolution and, in turn, completion of the adjacency.

For example, if the ARP table already lists a particular host, punting it to the process level does not trigger an ARP request. If an entry is incomplete (no response from ARP request) or incorrect in the ARP table, it is also incomplete or incorrect in the CEF adjacency table. This section covers reviewing the ARP table.

Example 4-2 illustrates sample output from the show arp command used to display the contents of the ARP table.

Example 4-2. Displaying the ARP Table in Cisco IOS

Router-2#show arp
Protocol  Address          Age (min)  Hardware Addr   Type   Interface
Internet  172.18.114.250          0   0007.e978.ef03  ARPA   Vlan114
Internet  172.18.114.244        237   0004.7553.cf3c  ARPA   Vlan114
Internet  172.18.114.243          0   Incomplete      ARPA   Vlan114

Based on the show arp command output, investigate whether the ARP table information is correct. In this example, you see three entries. The 172.18.114.243 entry is incomplete, which means that the device with the address 172.18.114.243 did not respond to the ARP request or is simply powered off. To verify whether the other listings are correct, you might need to access the end device and verify the locally configured MAC address.

Example 4-3 illustrates determining the IP address and MAC address of a Microsoft Windows XP laptop.

Example 4-3. Determining the IP Address and MAC Address of a Microsoft Windows XP Laptop

C:\WINDOWS\system32>ipconfig.exe /all

Windows IP Configuration

        Host Name . . . . . . . . . . . . : test-winxp
        Primary Dns Suffix  . . . . . . . : amer.bcmsn.com
        Node Type . . . . . . . . . . . . : Hybrid
        IP Routing Enabled. . . . . . . . : No
        WINS Proxy Enabled. . . . . . . . : No
        DNS Suffix Search List. . . . . . : cisco.com
                                            cisco.com

Ethernet adapter Local Area Connection 2:

        Connection-specific DNS Suffix  . : cisco.com
        Description . . . . . . . . . . . : (text deleted) Network Connection
        Physical Address. . . . . . . . . : 00-09-6B-60-15-74
        Dhcp Enabled. . . . . . . . . . . : Yes
        Autoconfiguration Enabled . . . . : Yes
        IP Address. . . . . . . . . . . . : 172.18.114.244
        Subnet Mask . . . . . . . . . . . : 255.255.0.0
        Default Gateway . . . . . . . . . : 172.18.114.1
        DHCP Server . . . . . . . . . . . : 10.18.0.1
        DNS Servers . . . . . . . . . . . : 10.2.2.1
        Lease Obtained. . . . . . . . . . : Saturday, February 12, 2005 12:08:5 PM
        Lease Expires . . . . . . . . . . : Sunday, February 13, 2005 12:38:59 PM

Ethernet adapter Wireless Network Connection 3:
        Media State . . . . . . . . . . . : Media disconnected
        Description . . . . . . . . . . . : Cisco Systems PCI Wireless LAN Adapter
        Physical Address. . . . . . . . . : 00-02-8A-3E-6D-CB

In Example 4-3, the MAC (physical) address of the host is 00-09-6B-60-15-74. This differs from the ARP table of the local router. A protocol analyzer such as Ethereal is necessary to decode frames on Ethernet to investigate why the router has an incorrect entry. Example 4-4 shows an example of troubleshooting ARP entries with the debug arp command.

Example 4-4. Troubleshooting Incorrect ARP Entries Using the debug arp Command

Router-2#debug arp
ARP packet debugging is on
Router-2#clear arp int vlan 114
*Feb 12 10:43:23.710 UTC: IP ARP: sent req src 172.18.114.4 0008.a378.bdff,
                 dst 172.18.114.250 0007.e978.ef03 Vlan114
*Feb 12 10:43:23.710 UTC: IP ARP: sent req src 172.18.114.4 0008.a378.bdff,
                 dst 172.18.114.244 0004.7553.cf3c Vlan114
*Feb 12 10:43:23.718 UTC: IP ARP: rcvd rep src 172.18.114.250 0007.e978.ef03, dst
  172.18.114.4 Vlan114
*Feb 12 10:43:23.718 UTC: IP ARP: creating entry for IP address: 172.18.114.250,
  hw: 0007.e978.ef03
*Feb 12 10:43:23.718 UTC: IP ARP: rcvd rep src 172.18.114.244 0009.6B60.1574, dst
  172.18.114.4 Vlan114
*Feb 12 10:43:23.718 UTC: IP ARP: creating entry for IP address: 172.18.114.244,
  hw: 0009.6B60.1574
*Feb 12 10:43:24.124 UTC: IP ARP: rcvd rep src 172.18.114.244 0004.7553.cf3c, dst
  172.18.114.4 Vlan114
*Feb 12 10:43:24.124 UTC: IP ARP: creating entry for IP address: 172.18.114.244,
  hw: 0004.7553.cf3c

From the debug output, it is apparent that two devices are replying to the ARP request sent by the router: the test host and a rogue or misconfigured device. The router always populates the ARP table with the most recent ARP response. Because the rogue entry arrived second, the ARP table was incorrect. Another example of invalid ARP entries is with Frame Relay point-to-point or other types of point-to-point interfaces. Because the ARP entry is incorrect, the CEF adjacency table entry will also be incorrect.

Verifying the Routing Table

The example in the previous section was based on a directly connected device. To illustrate verifying the IP routing table and subsequent CEF troubleshooting, Example 4-5 is based on a router with several routes, as illustrated in Figure 4-3. Devices connected to Router 2 in the 10.1.1.0/24 subnet are unable to reach a Secure File Transfer Protocol (SFTP) server with the address 10.18.118.184, as shown in the first steps of Example 4-5; specifically, the host 10.1.1.100 is unable to ping 172.18.118.184. For the purpose of this example, assume that all the IP routing configuration and host configurations, such as IP address and default gateways, are configured correctly. In addition, assume that our issue is strictly limited to Router 2 and not Router 1, the Layer 3 switch.

Figure 4-3

Figure 4-3 Troubleshooting IP Connectivity and Verifying the IP Routing Table

Example 4-5. IP Connectivity Issue from the Host, 10.1.1.100, to the Target, 172.18.118.184, Based on Figure 4-3

Host 10.1.1.100:

C:\WINDOWS\system32>ping 10.18.118.184

Pinging 172.18.118.184 with 32 bytes of data:

Request timed out.
Request timed out.
Request timed out.
Request timed out.

Ping statistics for 172.18.118.184:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),

C:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter Local Area Connection 2:

        Connection-specific DNS Suffix  . : cisco.com
        IP Address. . . . . . . . . . . . : 10.1.1.100
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 10.1.1.1

C:\WINDOWS\system32>tracert 10.18.118.183

Tracing route to 10.18.118.183 over a maximum of 30 hops

  1   <10 ms   <10 ms   <10 ms  Router-2.cisco.com [10.1.1.1]
  2     *        *        *     Request timed out.
  3     *        *        *     Request timed out.
  4     *        *        *     Request timed out.
  5     *        *        *     Request timed out.
  6     *        *        *     Request timed out.
!Output omitted

The first step in troubleshooting is to access the first-hop router, Router 2, and verify IP connectivity to the SFTP server, 10.18.118.184. Example 4-6 also confirms the route to the host, 10.18.118.184, and verifies the ARP entry for the next hop for 10.18.118.184, which is 10.18.114.1. The host entry, 10.18.118.184, is known through a static route with a metric of 0 according to the show ip route command. This is the gateway of last resort.

Example 4-6. Verifying IP Routing Table and Next-Hop Information

Router-2#ping 172.18.118.184

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.18.118.184, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms
Router-2#

Router-2#show ip route 172.18.118.184
Routing entry for 172.18.118.0/24
  Known via "static", distance 1, metric 0
  Routing Descriptor Blocks:
  * 172.18.114.1
      Route metric is 0, traffic share count is 1

Router-2#show ip arp 172.18.114.1
Protocol  Address          Age (min)  Hardware Addr   Type   Interface
Internet  172.18.114.1            0   0008.a37f.cb7c  ARPA   Vlan114

Router-2#show ip route 172.18.114.1
Routing entry for 172.18.114.0/24
  Known via "connected", distance 0, metric 0 (connected, via interface)
  Redistributing via ospf 1
  Routing Descriptor Blocks:
  * directly connected, via Ethernet0/0
      Route metric is 0, traffic share count is 1

Although the ping from the router was successful, the next step is to verify the MAC (Hardware Addr) of the next-hop router. This step verifies that the correct ARP entry exists for the next-hop router. Example 4-7 illustrates obtaining Router 1's MAC address for the interface configured with the IP address 172.18.114.1.

Example 4-7. Verifying the MAC Address of an Interface in Cisco IOS

Router-1#show interfaces vlan 114 | include address
!Output omitted
  Hardware is Cat6k RP Virtual Ethernet, address is 0008.a37f.cb7c (bia
0008.a37f.cb7c)
  Internet address is 172.18.114.1/24
!Output omitted

The next-hop router's (Router 1's) MAC address is indeed 0008.a37f.cb7c. Therefore, at this point in troubleshooting, both the routing entry and ARP entry for the next-hop router are correct.

The next step is to verify IP connectivity to the next-hop router, Router 1, from both the host, 10.1.1.100, and Router 2, as shown in Example 4-8.

Example 4-8. Verifying IP Connectivity to the Next Hop from Router 2 and the Host, 10.1.1.100

Router-2#ping 172.18.114.1

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.18.114.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms

Router-2#ping
Protocol [ip]:
Target IP address: 172.18.114.1
Repeat count [5]: 10
Datagram size [100]: 1500
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 10, 1500-byte ICMP Echos to 172.18.114.1, timeout is 2 seconds:
!!!!!!!!!!
Success rate is 100 percent (10/10), round-trip min/avg/max = 1/2/4 ms

Host 10.1.1.100:

C:\WINDOWS\system32>ping 172.18.114.1

Pinging 172.18.118.184 with 32 bytes of data:

Reply from 172.18.114.1: bytes=32 time=41ms TTL=253
Reply from 172.18.114.1: bytes=32 time=41ms TTL=253
Reply from 172.18.114.1: bytes=32 time=41ms TTL=253
Reply from 172.18.114.1: bytes=32 time=40ms TTL=253

Ping statistics for 172.18.114.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 40ms, Maximum = 41ms, Average = 40ms

Example 4-8 also issued an ICMP ping of a larger packet size for continued verification of accessibility of the next-hop router. You must verify various packet sizes because default-sized packets of ICMP echoes can be routed and switched correctly in the network, whereas larger packets can be dropped for a multitude of reasons. These reasons include encoding errors in WAN circuits, fragmentation configuration issues, hardware issues, Virtual Private Network (VPN) misconfiguration, software features such as encryption and compression, and so on. Some network routers' security policies can also prevent the routers from responding to very high rates of ICMP packets. Therefore, you should understand your network policies when troubleshooting or installing systems. In Example 4-8, the router is indeed reachable through ICMP.

Example 4-8 proved that the next hop is reachable from both Router 2 and the host, 10.1.1.100. Therefore, at this point, the ARP and IP routing tables appear to be correct on Router 2. The next step is troubleshooting CEF (Step 6), which is discussed in the next section using the same example as that in Figure 4-3.

Sending ICMP echoes, requests, or responses from the CLI of the router is software switched, while ICMP echoes from end devices through many Cisco IOS routers and all current-generation Catalyst switches are hardware switched. The software-switching path might be correct, but the hardware-switching path might not be correct. In this example, the software-switching path on Router 2 might be correct, but the hardware-switching path might not be correct. Troubleshooting the hardware-switching path is outside the scope of this chapter. Chapter 5 discusses troubleshooting hardware-switching paths on a Cisco Catalyst 6500 platform. However, you must troubleshoot CEF from the software-switching perspective first because the hardware-switching tables are built from the software-switching tables.

The section "Troubleshooting the CEF FIB Table," later in this chapter, continues the investigation of the software-switching path by troubleshooting the Cisco IOS CEF table on Router 2 for Figure 4-3. As noted previously, because the hardware-switching path gets built from the software-switching CEF and adjacency table, you should investigate the software-switching path first.

Using IOS Ping with the Record Option to Rule Out CEF

CEF does not support all IP packet types and must process-switch specific types of packets. One such packet includes the ICMP echo with the record option. As such, you can rule out CEF as a cause of an IP connectivity problem with some certainty using the ICMP echo with record option.

For example, in Figure 4-3, sending an ICMP echo with the record option forces all routers along the path to use the process-switching method of forwarding a frame. If an ICMP echo with the record option is successful and a standard ICMP echo is not, you can assume with some certainty that CEF is indeed a cause of your IP connectivity issue somewhere along the path.

In Cisco IOS, use the ping command with extended commands option to send ICMP echoes with the record option. Example 4-9 illustrates the use of the ICMP echo with record option.

Example 4-9. Sending ICMP Packets Using the Record Option

Router-2#ping ip
Target IP address: 10.18.118.184
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: loop 0
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]: r
Number of hops [ 9 ]:
Loose, Strict, Record, Timestamp, Verbose[RV]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.18.118.184, timeout is 2 seconds:
Packet has IP options:  Total option bytes= 39, padded length=40
 Record route: <*>
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)

Reply to request 0 (1 ms).  Received packet has options
 Total option bytes= 40, padded length=40
 Record route:
   (172.18.114.4)
   (10.18.118.1)
   (10.18.118.184)
   (172.18.114.4) <*>
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
   (0.0.0.0)
 End of list

!Output omitted for brevity

Troubleshooting the CEF FIB Table

The following sections outline basic CEF troubleshooting using a stepwise approach based on Figure 4-3 and Example 4-5. These sections move to focusing on CEF.

The steps for verifying the CEF table are as follows:

  • Step 1 Verify the CEF configuration.
  • Step 2 Confirm the IP CEF switching path, including using CEF accounting counters to confirm the switching path.
  • Step 3 Verify CEF switching details.

Verifying the CEF Configuration

When verifying the CEF table (FIB), first verify whether CEF is indeed enabled globally and on an interface basis using the following commands:

show ip cef
show cef interface <module_number>/<port_number>

Example 4-10 illustrates how to verify that CEF is indeed enabled on both a global and an interface basis.

Example 4-10. Verifying That IP CEF Is Enabled Globally and Per-Interface

Router-2#show ip cef
Prefix              Next Hop              Interface
0.0.0.0/0           172.18.114.1          Ethernet0/0
0.0.0.0/32          receive
10.0.0.0/24         172.18.114.1          Ethernet0/0
10.1.1.0/24         attached              Ethernet0/1
10.1.1.0/32         receive
10.1.1.1/32         receive
10.1.1.100/32       10.1.1.100            Ethernet0/1
10.1.1.255/32       receive
10.18.118.0/24      172.18.114.1          Ethernet0/0
10.224.0.0/24       172.18.114.1          Ethernet0/0
10.225.0.0/24       172.18.114.1          Ethernet0/0
10.226.0.0/24       172.18.114.1          Ethernet0/0
165.27.1.0/24       172.18.114.1          Ethernet0/0
172.18.114.0/24     attached              Ethernet0/0
172.18.114.0/32     receive
172.18.114.1/32     172.18.114.1          Ethernet0/0
172.18.114.4/32     receive
172.18.114.5/32     172.18.114.5          Ethernet0/0
172.18.114.7/32     172.18.114.7          Ethernet0/0
172.18.114.177/32   172.18.114.177        Ethernet0/0
172.18.114.191/32   172.18.114.191        Ethernet0/0
172.18.114.214/32   172.18.114.214        Ethernet0/0
Prefix              Next Hop              Interface
172.18.114.255/32   receive
172.18.116.64/29    172.18.114.1          Ethernet0/0
192.168.100.0/24    172.18.114.1          Ethernet0/0
224.0.0.0/4         drop
224.0.0.0/24        receive
255.255.255.255/32  receive

If CEF is not enabled globally, the show ip cef command returns the message "%CEF not running," as shown in Example 4-11.

Example 4-11. Example of Router Not Running CEF

Router-2#show ip cef

%CEF not running

Although the previous step shows that CEF is enabled on the interfaces in respect to Figure 4-3, the show ip interface and the show cef interface interface commands confirm that CEF is enabled on a per-interface basis. Example 4-12 illustrates the show ip interface command.

Example 4-12. Verifying That CEF Is Enabled on a Per-Interface Basis Using the show ip interface Command

Router-2#show ip interface ethernet 0/0
Ethernet0/0 is up, line protocol is up
  Internet address is 172.18.114.4/24
  Broadcast address is 255.255.255.255
  Address determined by setup command
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Multicast reserved groups joined: 224.0.0.5 224.0.0.6
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is disabled
  IP Flow switching is disabled
  IP CEF switching is enabled
  IP CEF Fast switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast, CEF
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Probe proxy name replies are disabled
  Policy routing is disabled
  Network address translation is disabled
  Web Cache Redirect is disabled
  BGP Policy Mapping is disabled

Router-2#show cef interface ethernet 0/0
Ethernet0/0 is up (if_number 2)
  Corresponding hwidb fast_if_number 2
  Corresponding hwidb firstsw->if_number 2
  Internet address is 172.18.114.4/24
  ICMP redirects are always sent
  Per packet load-sharing is disabled
  IP unicast RPF check is disabled
  Inbound access list is not set
  Outbound access list is not set
  IP policy routing is disabled
  BGP based policy accounting is disabled
  Hardware idb is Ethernet0/0
  Fast switching type 1, interface type 61
  IP CEF switching enabled
  IP CEF Feature Fast switching turbo vector
  Input fast flags 0x0, Output fast flags 0x0
  ifindex 1(1)
  Slot 0 Slot unit 0 Unit 0 VC -1
  Transmit limit accumulator 0x0 (0x0)
  IP MTU 1500

Confirming the IP CEF Switching Path

The next step in troubleshooting the CEF table is to verify the switching path that the router in question is using. The show interfaces stat command displays the switching path stats on Cisco IOS routers, as shown in Example 4-13. The processor row includes process-switched (software-switched) packets, while the router cache row includes both CEF-switched and fast-switched packets. Note that high-end routers and switches that support distributed CEF display an additional row referred to as Hardware, Parallel Express Forwarding (PXF), or Distributed.

Example 4-13. Displaying Interface Switching Statistics

Router-2#show interfaces stat
Ethernet0/0
          Switching path    Pkts In   Chars In    Pkts Out  Chars Out
               Processor     398302   28590641       34250    3035319
             Route cache        173      81340         192      12152
                   Total     398475   28671981       34442    3047471


Ethernet0/1
          Switching path    Pkts In   Chars In    Pkts Out  Chars Out
               Processor      14614    3087533      18038     1700974
             Route cache        191      12955        172       80920
                   Total      14805    3100488      18210     1781894

From Example 4-13, the router is using route cache for switching. The command does not tell you how much is CEF switched or how much is fast switched because route cache includes both CEF-switched and fast-switched packets. Another way to determine whether the router is fast-switching or CEF-switching packets is to view the contents of the fast-switching table using the show ip cache command. If prefix entries exist in the fast-switching table, the traffic to the destination entries are being fast switched. Example 4-14 illustrates using the show ip cache command to verify CEF switching.

Example 4-14. Viewing the Fast-Switching (IP Cache) Table

Router-2#show interface stat
Ethernet0/0
          Switching path    Pkts In   Chars In   Pkts Out  Chars Out
               Processor     400445   28741844      34413    3049576
             Route cache        416     128348        436      29516
                   Total     400861   28870192      34849    3079092
Interface Serial0/0 is disabled

Ethernet0/1
          Switching path    Pkts In   Chars In   Pkts Out  Chars Out
               Processor      14662    3099087      18119    1708563
             Route cache        436      30581        416     127949
                   Total      15098    3129668      18535    1836512

Router-2#show ip cache
IP routing cache 0 entries, 0 bytes
   2 adds, 2 invalidates, 0 refcounts
Minimum invalidation interval 2 seconds, maximum interval 5 seconds,
   quiet interval 3 seconds, threshold 0 requests
Invalidation rate 0 in last second, 0 in last 3 seconds
Last full cache invalidation occurred 1d18h ago

Prefix/Length          Age       Interface        Next Hop

Router-2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router-2(config)#no ip cef
Router-2(config)#end

Router-2#show ip cef
%CEF not running
Prefix              Next Hop             Interface

Router-2#show ip cache
IP routing cache 2 entries, 344 bytes
   4 adds, 2 invalidates, 0 refcounts
Minimum invalidation interval 2 seconds, maximum interval 5 seconds,
   quiet interval 3 seconds, threshold 0 requests
Invalidation rate 0 in last second, 0 in last 3 seconds
Last full cache invalidation occurred 1d18h ago

Prefix/Length          Age       Interface        Next Hop
10.1.1.100/32           00:00:10  Ethernet0/1      10.1.1.100
10.18.118.0/24          00:00:10  Ethernet0/0      172.18.114.1

Router-2#show interfaces stat
Ethernet0/0
          Switching path    Pkts In   Chars In   Pkts Out  Chars Out
               Processor     400665   28758026      34436    3051672
             Route cache        506     135008        525      36102
                   Total     401171   28893034      34961    3087774


Ethernet0/1
          Switching path    Pkts In   Chars In   Pkts Out  Chars Out
               Processor      14674    3101447      18131    1709787
             Route cache        524      37093        505     134535
                   Total      15198    3138540      18636    1844322

Router-2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router-2(config)#ip cef
Router-2(config)#end

Router-2#show ip cache
IP routing cache 0 entries, 0 bytes
   5 adds, 5 invalidates, 0 refcounts
Minimum invalidation interval 2 seconds, maximum interval 5 seconds,
   quiet interval 3 seconds, threshold 0 requests
Invalidation rate 0 in last second, 0 in last 3 seconds
Last full cache invalidation occurred 1d18h ago

Prefix/Length          Age       Interface       Next Hop

Router-2#

Example 4-14 illustrates that the route cache counters from the show interface stats command were CEF switched by the router in our example. Example 4-14 views the output of the show interface stats command, checks the fast-switching table using the show ip cache command, and then disables CEF. After disabling CEF, the fast-switching table was rechecked and entries were observed.

In reference to Figure 4-3, where the host 10.1.1.100 could not ping 10.18.118.184, the troubleshooting step of ruling in or ruling out CEF is to disable CEF switching, globally or per interface, and reattempt to send the ICMP echoes. Of course, in a production environment, disabling CEF might not be an option; however, during a change-control window or isolated situation, this troubleshooting is useful. Always consult with a Cisco Technical Assistance Center (TAC) engineer before disabling CEF.

When disabling CEF on a per-interface basis for troubleshooting, pay close attention to the ingress and egress interfaces. Generally, when disabling CEF on a per-interface basis for troubleshooting, disable CEF on both the ingress and egress interface. In a mixed-mode environment, where the ingress and egress interface use different switching configurations, refer to Table 4-1 for the resulting switching method.

Table 4-1. Resulting Switching Method Based on Ingress and Egress Switching Configuration

Ingress Interface

Egress Interface

Resulting Switching Method

CEF

Process

CEF

Process

CEF

Fast

Process

Fast Switching

Fast Switching

CEF

Fast Switching

CEF

Based on the information in Table 4-1, CEF switching occurs on the ingress. Therefore, use the no ip route-cache cef command on the ingress interface to disable CEF. In contrast, because Cisco IOS builds a fast-switching cache entry after switching a packet, packets ingress on a process-switched interface and egress through a fast-switched interface. Therefore, use the no ip route-cache command on the egress interface to disable fast switching. Alternatively, disabling CEF on a global basis is permissible on several platforms, mostly low-end platforms that use the no ip cef command. Check the release notes and configuration guide for your specific platform when attempting to disable CEF globally or per interface.

Furthermore, newer mid- to high-end platforms do not support disabling CEF on a global or per-interface basis. When attempting to disable CEF on a platform such as the Catalyst 6500, Cisco 12000, CRS, and Cisco 7600 that do not support disabling CEF, the CLI returns an error. Example 4-15 illustrates an example of attempting to disable CEF on a platform that does not support disabling CEF.

Example 4-15. Attempting to Disable CEF on a Platform Such as the Catalyst 4500 That Does Not Support Disabling CEF

Catalyst4500#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Catalyst4500(config)#no ip cef
%Cannot disable CEF on this platform

Using CEF Accounting Counters to Confirm the Switching Path

Cisco IOS supports CEF accounting, with specific limitations pertaining to hardware-switched traffic. However, with software switching, CEF supports an accounting option for packet and byte counters.

When troubleshooting CEF, you can view the packet and byte counters on a per-prefix basis. To enable CEF accounting, use the ip cef accounting per-prefix global configuration command. Simply use the show ip cef prefix command to display the counters for a specific prefix. Example 4-16 illustrates the use of CEF accounting.

Example 4-16. CEF Accounting

Router-2#configure terminal
Router-2(config)#ip cef accounting per-prefix
Router-2(config)#end
Router-2#show ip cef 10.18.118.84
10.18.118.0/24, version 53, epoch 0, cached adjacency 172.18.114.1
240 packets, 14400 bytes
  via 172.18.114.1, Ethernet0/0, 0 dependencies
    next hop 172.18.114.1, Ethernet0/0
    valid cached adjacency

Verifying the CEF Switching Details

In most production environments, you usually cannot disable CEF, even on a per-interface basis, during normal production. This is because in many production networks, traffic rates exceed the software-switching capabilities of the router, and disabling CEF forces software switching. Therefore, disabling CEF to troubleshoot CEF is not always an option. The next step in these situations is to verify the CEF table information.

Example 4-17 illustrates the use of the show ip cef command to gather details about the CEF table on a per-entry basis. The values chosen for this example match those for the troubleshooting example.

Example 4-17. Gathering CEF Table Details

Router-2#show ip cef 10.18.118.184 detail
10.18.118.0/24, version 23, cached adjacency 172.18.114.1
0 packets, 0 bytes
  via 172.18.114.1, Ethernet0/0, 0 dependencies
     next hop 172.18.114.1, Ethernet0/0
     valid cached adjacency

Router-2#show ip cef 172.18.114.1 detail
172.18.114.1/32, version 17, cached adjacency 172.18.114.1
0 packets, 0 bytes
  via 172.18.114.1, Ethernet0/0, 1 dependency
    next hop 172.18.114.1, Ethernet0/0
    valid cached adjacency

From the output shown in Example 4-17, the host 10.18.118.184 next hop is 172.18.114.1 and is a valid cached adjacency through Ethernet0/0. The first step is to verify this output against Figure 4-3 and the show ip route command from Example 4-5. The details are correct. The next step is to verify the next-hop CEF entry for 10.18.118.184, which is 172.18.114.1. Again, this information appears to be correct based on Figure 4-3. If this information was not correct, the next step is to either disable CEF and test connectivity or open a Cisco TAC case.

Another possible reason for packet loss with CEF is CEF drop adjacency. CEF drop adjacencies define hardware-switched drops for prefixes. CEF drop adjacencies allow dropping frames in hardware rather than punting every frame for software switching. This is an effective method in preventing denial of service (DoS) attacks and high CPU usage due the CPU processing excessive drops. If a CEF drop adjacency exists, it is generally because of one of the following reasons:

  • Unsupported features.
  • Packets destined to prefixes associated with punt adjacencies that exceed a predefined rate. Punting rate limiters exist to prevent DoS attacks and high CPU usage caused by excessive punts.
  • Unresolved or missing FIB entry.
  • Unsupported frame type.

Example 4-18 illustrates a sample output from the show cef drop command. In respect to Figure 4-3 and Example 4-5, attempting to relate the CEF drop counters to the ICMP packets can yield additional details about why the packets are being dropped. However, in a production environment, it is difficult to correlate the ICMP packet loss to show cef drop counters because production environments generally have multiple flows passing traffic simultaneously. Nonetheless, if the show cef drop counters remain 0 during the ping tests, you can rule out the notion that the ping failed because of CEF drop adjacencies. In later code, the show ip cef switching statistics command gives detailed information about why a drop occurs and replaces the show cef not command.

Example 4-18. show cef drop Command Example

Router-2#show cef drop
CEF Drop Statistics
Slot  Encap_fail  Unresolved Unsupported    No_route       No_adj  ChkSum_Err
RP             3           0           0           0            0           0

Table 4-2 defines the fields associated with the show cef drop command.

Table 4-2. show cef drop Field Descriptions

Field

Description

Slot

Refers to the slot for the respective ingress packet counts. For Cisco IOS routers that do not support dCEF, this value is always RP.

Encap_fail

Indicates the number of packets dropped after exceeding the limit for packets punted to the processor because of missing adjacency information such as an unresolved ARP request. Note that CEF throttles packets punted to the process level at a rate of one packet per second to aid in susceptibility of DoS attacks.

Unresolved

Indicates the number of packets dropped because of an unresolved prefix in the FIB table.

Unsupported

Indicates the number of packets fast-dropped by CEF (drop adjacency) because of an unsupported feature.

No_route

Indicates the number of packets dropped because of a missing prefix in the FIB table.

No_adj

Indicates the number of packets dropped because of incomplete adjacency.

Chksum_Err

Indicates the number of IP version 4 (IPv4) packets received with a checksum error.

In controlled environments, preferably in nonproduction environments, use debugs to troubleshoot CEF. If you can narrow your issue to a specific host or subnet and the router or switch under investigation is logging drops or receives, you can use debugs that are limited to specific destinations to troubleshoot the issue. Limiting debugs is done by limiting debug output to specific IP sources or destinations configured in an access list. Example 4-19 illustrates an example of configuring an access control list (ACL) to limit the output of a CEF debug to a specific destination.

Example 4-19. Controlling Debug Output Defined by an ACL

Router-2#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router-2(config)#access-list 10 permit 10.1.1.1
Router-2(config)#end

Router-2#debug ip cef drop 10
IP CEF drops debugging is on for access list 10
Router-2#debug ip cef receive 10
IP CEF received packets debugging is on for access list 10

*Mar  7 23:27:29.681 UTC: CEF-receive: Receive packet for 10.1.1.1
*Mar  7 23:27:29.681 UTC: CEF-Receive: Packet for 10.1.1.1 -- receive
*Mar  7 23:27:29.681 UTC: IP-CEF: Receive packet for 10.1.1.1 (process switch)

Based on the example in Figure 4-3 and Example 4-5, the debug output illustrates the router processing "receive" packets destined for its own interface. Receive packets include packets punted by CEF for software switching. Drop packets appear in the debug output in the same manner. As a result, this debug, used in controlled environments, can yield additional information helpful in troubleshooting.

Verifying the Adjacency Table

After verifying the CEF FIB table, the next step in troubleshooting CEF is to verify the adjacency table. The adjacency table contains the rewrite information that CEF uses to switch packets. Verifying that the rewrite information is correct is an important step in troubleshooting CEF operation.

The four commands that provide different hierarchical levels of information for the adjacency table are show adjacency, show adjacency summary, show adjacency detail, and show adjacency internal. Example 4-20 shows examples of these commands, respectively.

Example 4-20. Viewing Adjacency Table Details

Router-2#show adjacency
Protocol Interface                 Address
IP       Ethernet0/1               10.1.1.100(5)
!Output omitted for brevity
IP       Ethernet0/0               172.18.114.1(23)

Router-2#show adjacency summary
Adjacency Table has 6 adjacencies
  Table epoch: 0 (6 entries at this epoch)

  Interface                 Adjacency Count
  Ethernet0/0               5
  Ethernet0/1               1

Router-2#show adjacency detail
Protocol Interface                 Address
!Output omitted for brevity
IP       Ethernet0/1               10.1.1.100(5)
                                   561 packets, 41514 bytes
                                   0007E905156C00503EFA37810800
                                   ARP        03:53:37
                                   Epoch: 0
!Output omitted for brevity
IP       Ethernet0/0               172.18.114.1(23)
                                   581 packets, 43012 bytes
Protocol Interface                 Address
                                   0008A37FCB7C00503EFA37800800
                                   ARP        04:02:59
                                   Epoch: 0

Router-2#show adjacency internal
Protocol Interface                 Address
!Output omitted for brevity
IP       Ethernet0/0               172.18.114.1(23)
                                   280 packets, 20738 bytes
                                   0008A37FCB7C00503EFA37800800
                                   ARP        04:02:58
                                   Epoch: 0
                                   Fast adjacency disabled
                                   IP redirect enabled
                                   IP mtu 1500 (0x0)
                                   Fixup disabled
                                   Adjacency pointer 0x816BFC20, refCount 23
                                   Connection Id 0x000000
                                   Bucket 205
IP       Ethernet0/1               10.1.1.100(5)
                                   269 packets, 19906 bytes
                                   0007E905156C00503EFA37810800
                                   ARP        03:58:29
                                   Epoch: 0
                                   Fast adjacency disabled
                                   IP redirect enabled
                                   IP mtu 1500 (0x0)
                                   Fixup disabled
                                   Adjacency pointer 0x816BFAD0, refCount 5
                                   Connection Id 0x000000
                                   Bucket 110
!Output omitted for brevity

Table 4-3 describes the most significant fields from the show adjacency commands in Example 4-20 for the purpose of troubleshooting. Verifying the information against the show ip route and show arp commands is necessary in verifying CEF consistency. If the values are not correct, disable CEF as a workaround and open a Cisco TAC case.

Table 4-3. show adjacency Command Field Descriptions

Field

Description

172.18.114.1(23)

The value in parentheses, 23, refers to the number of times a FIB entry points to an adjacency entry (refCount). Numerous system entries are not shown in the output of the show ip cef command. In the hardware used for this example, a minimum of five references per IP address existed. As a result, four additional FIB routing entries point to the IP address.

0008A37FCB7C0008A 378BDFF0800

The first 12 characters, 0008A37FCB7C, are the MAC address associated with the destination next-hop interface (destination MAC address rewrite). The next 12 characters represent the MAC address of the source interface of the packet (source MAC address rewrite). The last four characters represent the well-known Ethertype value 0x0800 for IP for Advanced Research Projects Agency (ARPA) encapsulation, the default among Ethernet vendors.

ARP 04:02:58

The ARP value indicates that the entry was learned through the ARP process. The timestamp indicates the time remaining before the entry times out. The default ARP timeout is 4 hours.

Fast adjacency disabled

An FIB entry caches an adjacency for a next-hop interface when not doing load sharing over multiple active paths. A fast adjacency increases the switching speed of packets.

In Figure 4-3 and Example 4-5, the destination MAC address rewrite information from the show adjacency detail command in Example 4-20, 0008A37FCB7C, must match the MAC address from the show arp command. Otherwise, if the MAC address did not match, an inconsistency issue exists between the ARP table and adjacency table that needs to be investigated with the Cisco TAC.

Hardware-Specific Troubleshooting

If you are troubleshooting CEF on a Cisco IOS router that is only performing software switching and are unable to find any issues based on the previous sections, the next step is to open a Cisco TAC case and include relevant information. However, if you are troubleshooting a platform that supports dCEF or hardware switching, more analysis is needed.

Chapter 5 provides information on troubleshooting hardware switching on a Cisco Catalyst 6500. Example 4-21 illustrates performing troubleshooting of dCEF by examining the hardware-switching adjacency table on a Catalyst 4500 switch.

Example 4-21. Viewing a Hardware-Switching Adjacency Table

Router-2#show platform hardware ip adjacency host ip 172.18.114.1
32757: src: 00:08:A3:78:BD:FF dst: 00:08:A3:7F:CB:7C
       lbc: 0 vlan: 114 port: 248 (Gi1/1) sifact: FwdToCpu
       ifaid: 4086 packets: 290226195 bytes: 249761629484085 size: 1 refs: 3
       age: 2856047.074sec umda: flood
       vlanId: 114 single: true shar: true
       ifa: (4086) int: Vl114 (vlan 114) 172.18.114.1 00:08:A3:7F:CB:7C normal
2. Troubleshooting Punt Adjacencies | Next Section

Cisco Press Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Cisco Press and its family of brands. I can unsubscribe at any time.

Overview

Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Cisco Press products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@ciscopress.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security

Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children

This site is not directed to children under the age of 13.

Marketing

Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out

Users can always make an informed choice as to whether they should proceed with certain services offered by Cisco Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.ciscopress.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links

This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020